Merge branch 'master' into robolager2026

README.md

@@ -84,7 +84,7 @@ Additional articles:
 |*Boost converter (optional, for more stable power supply)*|*5V output*|<img src="docs/img/buck-boost.jpg" width=100>|1|
 |Motor|8520 3.7V brushed motor.<br>Motor with exact 3.7V voltage is needed, not ranged working voltage (3.7V — 6V).<br>Make sure the motor shaft diameter and propeller hole diameter match!|<img src="docs/img/motor.jpeg" width=100>|4|
 |Propeller|55 mm or 65 mm|<img src="docs/img/prop.jpg" width=100>|4|
-|MOSFET (transistor)|100N03A or [analog](https://t.me/opensourcequadcopter/33)|<img src="docs/img/100n03a.jpg" width=100>|4|
+|MOSFET (transistor)|UMW 100N03A or [analog](https://t.me/opensourcequadcopter/33).<br>Warning: don't use KIA 100N03A or other manufacturers, they might not work!|<img src="docs/img/100n03a.jpg" width=100>|4|
 |Pull-down resistor<br>Voltage measurement resistor|10 kΩ|<img src="docs/img/resistor10k.jpg" width=100>|6|
 |3.7V Li-Po battery|LW 952540 (or any compatible by the size).<br>Make sure the battery has enough discharge rate — 25C or more!|<img src="docs/img/battery.jpg" width=100>|1|
 |Battery connector cable|MX2.0 2P female|<img src="docs/img/mx.png" width=100>|1|

docs/user.md

@@ -4,6 +4,15 @@ This page contains user-built drones based on the Flix project. Publish your pro
 
 ---
 
+Author: Alican Erüst.<br>
+Description: QX95 mm frame, 55 mm propellers, 3.7 V 25C 1050 mAh LiPo battery, MPU6050 IMU, Logitech F310 gamepad controller, with a total quadcopter weight of 66 g.
+
+<img src="img/user/alicanerus/1.jpg" height=200> <img src="img/user/alicanerus/2.jpg" height=200> <img src="img/user/alicanerus/3.jpg" height=200>
+
+[Flight video](https://drive.google.com/file/d/1k0WeWTKnCAfaugkX7LcmNxsUuq79RL8Z/view?usp=sharing).
+
+---
+
 Author: [Неруш Михаил](https://t.me/NerushMV).<br>
 Description: custom frame made of 4 mm plywood, 8520 brushed motors, 75 mm propellers, MPU-6500. FlySky FS-i6X with ESP32-based adapter for ESP-NOW communication (using PPM output).<br>
 Sources and materials: [link](https://drive.google.com/drive/folders/1uWiDcuorLrtVs_IIR7Y13omij-7Q1nx8).

flix/cli.ino

@@ -50,8 +50,8 @@ const char* motd =
 "sta <ssid> <password> - configure Wi-Fi client mode\n"
 "espnow <mac> [<key>] - configure ESP-NOW peer\n"
 "mot - show motor output\n"
+"mfr/mfl/mrr/mrl [<thrust>] - test motor (remove props)\n"
 "log [dump] - print log header [and data]\n"
-"mfr, mfl, mrr, mrl - test motor (remove props)\n"
 "log - show log info\n"
 "log header - show log header\n"
 "log reset - reset log\n"
@@ -176,13 +176,13 @@ void doCommand(String str, bool echo = false) {
 	} else if (command == "ca") {
 		calibrateAccel();
 	} else if (command == "mfr") {
-		testMotor(MOTOR_FRONT_RIGHT);
+		testMotor(MOTOR_FRONT_RIGHT, arg0.isEmpty() ? 0.2 : arg0.toFloat());
 	} else if (command == "mfl") {
-		testMotor(MOTOR_FRONT_LEFT);
+		testMotor(MOTOR_FRONT_LEFT, arg0.isEmpty() ? 0.2 : arg0.toFloat());
 	} else if (command == "mrr") {
-		testMotor(MOTOR_REAR_RIGHT);
+		testMotor(MOTOR_REAR_RIGHT, arg0.isEmpty() ? 0.2 : arg0.toFloat());
 	} else if (command == "mrl") {
-		testMotor(MOTOR_REAR_LEFT);
+		testMotor(MOTOR_REAR_LEFT, arg0.isEmpty() ? 0.2 : arg0.toFloat());
 	} else if (command == "sys") {
 #ifdef ESP32
 		print("Chip: %s\n", ESP.getChipModel());

flix/motors.ino

@@ -51,9 +51,9 @@ bool motorsActive() {
 	return motors[0] != 0 || motors[1] != 0 || motors[2] != 0 || motors[3] != 0;
 }
 
-void testMotor(int n) {
+void testMotor(int n, float thrust) {
 	print("Testing motor %d\n", n);
-	motors[n] = 0.2;
+	motors[n] = thrust;
 	delay(50); // ESP32 may need to wait until the end of the current cycle to change duty https://github.com/espressif/arduino-esp32/issues/5306
 	sendMotors();
 	pause(3);

gazebo/flix.h

@@ -38,7 +38,7 @@ const char* getModeName();
 void sendMotors();
 int getDutyCycle(float value);
 bool motorsActive();
-void testMotor(int n);
+void testMotor(int, float);
 void print(const char* format, ...);
 void pause(float duration);
 void doCommand(String str, bool echo);