Group control parameters

Also add IMU group to accelerometer calibration parameters.

.github/workflows/tools.yml

@@ -46,3 +46,14 @@ jobs:
         echo -e "t,x,y,z\n0,1,2,3\n1,4,5,6" > log.csv
         ./csv_to_mcap.py log.csv
         test $(stat -c %s log.mcap) -eq 883
+
+  sloc:
+    runs-on: ubuntu-latest
+    steps:
+    - uses: actions/checkout@v4
+    - name: Install cloc
+      run: sudo apt-get install -y cloc
+    - name: Firmware source lines count
+      run: cloc --by-file-by-lang flix
+    - name: Overall source lines count
+      run: cloc --by-file-by-lang --exclude-ext=svg,dae,css,hbs,md,json,yaml,yml,toml .

.markdownlint.json

@@ -7,7 +7,6 @@
 	"MD024": false,
 	"MD033": false,
 	"MD034": false,
-	"MD059": false,
 	"MD044": {
 		"html_elements": false,
 		"code_blocks": false,
@@ -65,6 +64,5 @@
 			"PX4"
 		]
 	},
-	"MD045": false,
-	"MD060": false
+	"MD045": false
 }

.vscode/c_cpp_properties.json

@@ -18,7 +18,20 @@
 			"forcedInclude": [
 				"${workspaceFolder}/.vscode/intellisense.h",
 				"~/.arduino15/packages/esp32/hardware/esp32/3.2.0/cores/esp32/Arduino.h",
-				"~/.arduino15/packages/esp32/hardware/esp32/3.2.0/variants/d1_mini32/pins_arduino.h"
+				"~/.arduino15/packages/esp32/hardware/esp32/3.2.0/variants/d1_mini32/pins_arduino.h",
+				"${workspaceFolder}/flix/cli.ino",
+				"${workspaceFolder}/flix/control.ino",
+				"${workspaceFolder}/flix/estimate.ino",
+				"${workspaceFolder}/flix/flix.ino",
+				"${workspaceFolder}/flix/imu.ino",
+				"${workspaceFolder}/flix/led.ino",
+				"${workspaceFolder}/flix/log.ino",
+				"${workspaceFolder}/flix/mavlink.ino",
+				"${workspaceFolder}/flix/motors.ino",
+				"${workspaceFolder}/flix/rc.ino",
+				"${workspaceFolder}/flix/time.ino",
+				"${workspaceFolder}/flix/wifi.ino",
+				"${workspaceFolder}/flix/parameters.ino"
 			],
 			"compilerPath": "~/.arduino15/packages/esp32/tools/esp-x32/2411/bin/xtensa-esp32-elf-g++",
 			"cStandard": "c11",
@@ -52,7 +65,20 @@
 			"forcedInclude": [
 				"${workspaceFolder}/.vscode/intellisense.h",
 				"~/Library/Arduino15/packages/esp32/hardware/esp32/3.2.0/cores/esp32/Arduino.h",
-				"~/Library/Arduino15/packages/esp32/hardware/esp32/3.2.0/variants/d1_mini32/pins_arduino.h"
+				"~/Library/Arduino15/packages/esp32/hardware/esp32/3.2.0/variants/d1_mini32/pins_arduino.h",
+				"${workspaceFolder}/flix/flix.ino",
+				"${workspaceFolder}/flix/cli.ino",
+				"${workspaceFolder}/flix/control.ino",
+				"${workspaceFolder}/flix/estimate.ino",
+				"${workspaceFolder}/flix/imu.ino",
+				"${workspaceFolder}/flix/led.ino",
+				"${workspaceFolder}/flix/log.ino",
+				"${workspaceFolder}/flix/mavlink.ino",
+				"${workspaceFolder}/flix/motors.ino",
+				"${workspaceFolder}/flix/rc.ino",
+				"${workspaceFolder}/flix/time.ino",
+				"${workspaceFolder}/flix/wifi.ino",
+				"${workspaceFolder}/flix/parameters.ino"
 			],
 			"compilerPath": "~/Library/Arduino15/packages/esp32/tools/esp-x32/2411/bin/xtensa-esp32-elf-g++",
 			"cStandard": "c11",
@@ -87,7 +113,20 @@
 			"forcedInclude": [
 				"${workspaceFolder}/.vscode/intellisense.h",
 				"~/AppData/Local/Arduino15/packages/esp32/hardware/esp32/3.2.0/cores/esp32/Arduino.h",
-				"~/AppData/Local/Arduino15/packages/esp32/hardware/esp32/3.2.0/variants/d1_mini32/pins_arduino.h"
+				"~/AppData/Local/Arduino15/packages/esp32/hardware/esp32/3.2.0/variants/d1_mini32/pins_arduino.h",
+				"${workspaceFolder}/flix/cli.ino",
+				"${workspaceFolder}/flix/control.ino",
+				"${workspaceFolder}/flix/estimate.ino",
+				"${workspaceFolder}/flix/flix.ino",
+				"${workspaceFolder}/flix/imu.ino",
+				"${workspaceFolder}/flix/led.ino",
+				"${workspaceFolder}/flix/log.ino",
+				"${workspaceFolder}/flix/mavlink.ino",
+				"${workspaceFolder}/flix/motors.ino",
+				"${workspaceFolder}/flix/rc.ino",
+				"${workspaceFolder}/flix/time.ino",
+				"${workspaceFolder}/flix/wifi.ino",
+				"${workspaceFolder}/flix/parameters.ino"
 			],
 			"compilerPath": "~/AppData/Local/Arduino15/packages/esp32/tools/esp-x32/2411/bin/xtensa-esp32-elf-g++.exe",
 			"cStandard": "c11",

README.md

@@ -1,9 +1,6 @@
-<!-- markdownlint-disable MD041 -->
+# Flix
 
-<p align="center">
-  <img src="docs/img/flix.svg" width=180 alt="Flix logo"><br>
-  <b>Flix</b> (<i>flight + X</i>) — open source ESP32-based quadcopter made from scratch.
-</p>
+**Flix** (*flight + X*) — open source ESP32-based quadcopter made from scratch.
 
 <table>
   <tr>

docs/book/firmware.md

@@ -35,7 +35,7 @@
 
 ### Подсистема управления
 
-Состояние органов управления обрабатывается в функции `interpretControls()` и преобразуется в **команду управления**, которая включает следующее:
+Состояние органов управления обрабатывается в функции `interpretControls()` и преобразуется в *команду управления*, которая включает следующее:
 
 * `attitudeTarget` *(Quaternion)* — целевая ориентация дрона.
 * `ratesTarget` *(Vector)* — целевые угловые скорости, *рад/с*.

docs/firmware.md

@@ -38,13 +38,13 @@ Utility files:
 
 ### Control subsystem
 
-Pilot inputs are interpreted in `interpretControls()`, and then converted to the **control command**, which consists of the following:
+Pilot inputs are interpreted in `interpretControls()`, and then converted to the *control command*, which consists of the following:
 
 * `attitudeTarget` *(Quaternion)* — target attitude of the drone.
 * `ratesTarget` *(Vector)* — target angular rates, *rad/s*.
 * `ratesExtra` *(Vector)* — additional (feed-forward) angular rates , used for yaw rate control in STAB mode, *rad/s*.
 * `torqueTarget` *(Vector)* — target torque, range [-1, 1].
-* `thrustTarget` *(float)* — collective motor thrust target, range [0, 1].
+* `thrustTarget` *(float)* — collective thrust target, range [0, 1].
 
 Control command is handled in `controlAttitude()`, `controlRates()`, `controlTorque()` functions. Each function may be skipped if the corresponding control target is set to `NAN`.
 
@@ -62,11 +62,6 @@ print("Test value: %.2f\n", testValue);
 
 In order to add a console command, modify the `doCommand()` function in `cli.ino` file.
 
-> [!IMPORTANT]
-> Avoid using delays in in-flight commands, it will **crash** the drone! (The design is one-threaded.)
->
-> For on-the-ground commands, use `pause()` function, instead of `delay()`. This function allows to pause in a way that MAVLink connection will continue working.
-
 ## Building the firmware
 
 See build instructions in [usage.md](usage.md).

docs/img/flix.svg

@@ -1,38 +0,0 @@
-<svg xmlns="http://www.w3.org/2000/svg" viewBox="0 0 734.86 378.46">
-  <defs>
-    <style>
-      .a {
-        fill: none;
-        stroke: #d5d5d5;
-        stroke-miterlimit: 10;
-        stroke-width: 31px;
-      }
-
-      .b {
-        fill: #c1c1c1;
-      }
-
-      .c {
-        fill: #ff9400;
-      }
-
-      .d {
-        fill: #d5d5d5;
-      }
-    </style>
-  </defs>
-  <g>
-    <g>
-      <line class="a" x1="448.78" y1="294.23" x2="648.77" y2="93.24"/>
-      <line class="a" x1="449.78" y1="94.24" x2="649.77" y2="295.23"/>
-      <circle class="b" cx="549.27" cy="193.73" r="41.5"/>
-      <circle class="c" cx="449.35" cy="93.74" r="77.95"/>
-      <circle class="c" cx="648.89" cy="93.53" r="77.95"/>
-      <circle class="c" cx="647.89" cy="294.51" r="77.95"/>
-      <circle class="c" cx="448.9" cy="294.51" r="77.95"/>
-    </g>
-    <path class="d" d="M8,161.93q0-17.85,22.36-17.85h4.81V100.57Q35.17,8.49,131.23,8h1q36.87,0,47.31,7.48L181,17.41l1,2.41V50q0,12.32-5.82,12.31-2.43,0-7.4-4.64t-14.19-9a48.63,48.63,0,0,0-21.22-4.41q-12,0-19.17,3.5a18.85,18.85,0,0,0-9.82,10.62,67.35,67.35,0,0,0-3.52,12.06,82.52,82.52,0,0,0-.85,13.39v60.32h27.28q10.86,0,16.05,5.43a17.52,17.52,0,0,1,5.19,12.42,22.5,22.5,0,0,1-1.21,7.36q-1.22,3.51-6.64,7.24t-14.36,3.74H101.64V344.82a56,56,0,0,1-.61,9.65,37.8,37.8,0,0,1-2.56,7.6,11.83,11.83,0,0,1-6.94,6.4q-5,1.93-13.51,1.93H57.08q-10.47,0-15.7-4.71t-5.73-8.44a77.31,77.31,0,0,1-.48-9.53V180.27H29.4Q8,180.27,8,161.93Z"/>
-    <path class="d" d="M201.21,348.2V37q0-23.16,20.86-23.4h22.81q22.8,0,22.8,22.44V346.27a68.92,68.92,0,0,1-.49,9.41,22.59,22.59,0,0,1-2.42,7.12,11.48,11.48,0,0,1-6.67,5.43,47.78,47.78,0,0,1-12.74,2.17H225q-11.4,0-17.58-4.47T201.21,348.2Z"/>
-    <path class="d" d="M284.9,61.08V36.47a40.39,40.39,0,0,1,1.7-12.91,11.36,11.36,0,0,1,6.18-7,25.27,25.27,0,0,1,6.68-2.3c1.45-.15,4-.4,7.76-.72h25.23q10.43,0,16.73,4.7t6.31,18.22V62.05a27.94,27.94,0,0,1-.85,7.11,23,23,0,0,1-2.06,5.43,20,20,0,0,1-2.91,4,10,10,0,0,1-3.52,2.54c-1.21.48-2.54,1-4,1.44a11.53,11.53,0,0,1-3.4.73,13.71,13.71,0,0,0-3.15.48H307.7q-10.43,0-16.61-4.7T284.9,61.08Zm1.94,284.71V166.28q0-22.2,21.83-22.2h20.38q10.92,0,16.62,4t6.67,8.45a60.47,60.47,0,0,1,1,12.18V348.2q0,22.2-21.83,22.2H308.67q-10.43,0-15.64-4.95t-5.7-8.81A90.93,90.93,0,0,1,286.84,345.79Z"/>
-  </g>
-</svg>

docs/troubleshooting.md

@@ -4,7 +4,7 @@
 
 Do the following:
 
-* **Check ESP32 core is installed**. Check if the version matches the one used in the [tutorial](usage.md#building-the-firmware).
+* **Check ESP32 core is installed**. Check if the version matches the one used in the [tutorial](usage.md#firmware).
 * **Check libraries**. Install all the required libraries from the tutorial. Make sure there are no MPU9250 or other peripherals libraries that may conflict with the ones used in the tutorial.
 * **Check the chosen board**. The correct board to choose in Arduino IDE for ESP32 Mini is *WEMOS D1 MINI ESP32*.
 
@@ -25,7 +25,7 @@ Do the following:
   * The `accel` and `gyro` fields should change as you move the drone.
 * **Calibrate the accelerometer.** if is wasn't done before. Type `ca` command in Serial Monitor and follow the instructions.
 * **Check the attitude estimation**. Connect to the drone using QGroundControl. Rotate the drone in different orientations and check if the attitude estimation shown in QGroundControl is correct.
-* **Check the IMU orientation is set correctly**. If the attitude estimation is rotated, set the correct IMU orientation as described in the [tutorial](usage.md#define-imu-orientation).
+* **Check the IMU orientation is set correctly**. If the attitude estimation is rotated, make sure `rotateIMU` function is defined correctly in `imu.ino` file.
 * **Check the motors type**. Motors with exact 3.7V voltage are needed, not ranged working voltage (3.7V — 6V).
 * **Check the motors**. Perform the following commands using Serial Monitor:
   * `mfr` — should rotate front right motor (counter-clockwise).

docs/usage.md

@@ -12,7 +12,7 @@ Beginners can [download the source code as a ZIP archive](https://github.com/oka
 
 ## Building the firmware
 
-You can build and upload the firmware using either **Arduino IDE** (easier for beginners) or **command line**.
+You can build and upload the firmware using either **Arduino IDE** (easier for beginners) or a **command line**.
 
 ### Arduino IDE (Windows, Linux, macOS)
 
@@ -73,6 +73,14 @@ ICM20948 imu(SPI);  // For ICM-20948
 MPU6050 imu(Wire);  // For MPU-6050
 ```
 
+### Setup the IMU orientation
+
+The IMU orientation is defined in `rotateIMU` function in the `imu.ino` file. Change it so it converts the IMU axes to the drone's axes correctly. **Drone axes are X forward, Y left, Z up**:
+
+<img src="img/drone-axes.svg" width="200">
+
+See various [IMU boards axes orientations table](https://github.com/okalachev/flixperiph/?tab=readme-ov-file#imu-axes-orientation) to help you set up the correct orientation.
+
 ### Connect using QGroundControl
 
 QGroundControl is a ground control station software that can be used to monitor and control the drone.
@@ -80,7 +88,7 @@ QGroundControl is a ground control station software that can be used to monitor
 1. Install mobile or desktop version of [QGroundControl](https://docs.qgroundcontrol.com/master/en/qgc-user-guide/getting_started/download_and_install.html).
 2. Power up the drone.
 3. Connect your computer or smartphone to the appeared `flix` Wi-Fi network (password: `flixwifi`).
-4. Launch QGroundControl app. It should connect and begin showing the drone's telemetry automatically.
+4. Launch QGroundControl app. It should connect and begin showing the drone's telemetry automatically
 
 ### Access console
 
@@ -96,37 +104,11 @@ To access the console using QGroundControl:
 
 1. Connect to the drone using QGroundControl app.
 2. Go to the QGroundControl menu ⇒ *Vehicle Setup* ⇒ *Analyze Tools* ⇒ *MAVLink Console*.
-
-<img src="img/cli.png" width="400">
+   <img src="img/cli.png" width="400">
 
 > [!TIP]
 > Use `help` command to see the list of available commands.
 
-### Access parameters
-
-The drone is configured using parameters. To access and modify them, go to the QGroundControl menu ⇒ *Vehicle Setup* ⇒ *Parameters*:
-
-<img src="img/parameters.png" width="400">
-
-You can also work with parameters using `p` command in the console.
-
-### Define IMU orientation
-
-Use parameters, to define the IMU board axes orientation relative to the drone's axes: `IMU_ROT_ROLL`, `IMU_ROT_PITCH`, and `IMU_ROT_YAW`.
-
-The drone has *X* axis pointing forward, *Y* axis pointing left, and *Z* axis pointing up, and the supported IMU boards have *X* axis pointing to the pins side and *Z* axis pointing up from the component side:
-
-<img src="img/imu-axes.png" width="200">
-
-Use the following table to set the parameters for common IMU orientations:
-
-|Orientation|Parameters|Orientation|Parameters|
-|:-:|-|-|-|
-|<img src="img/imu-rot-1.png" width="180">|`IMU_ROT_ROLL` = 0<br>`IMU_ROT_PITCH` = 0<br>`IMU_ROT_YAW` = 0    |<img src="img/imu-rot-5.png" width="180">|`IMU_ROT_ROLL` = 3.142<br>`IMU_ROT_PITCH` = 0<br>`IMU_ROT_YAW` = 0|
-|<img src="img/imu-rot-2.png" width="180">|`IMU_ROT_ROLL` = 0<br>`IMU_ROT_PITCH` = 0<br>`IMU_ROT_YAW` = 1.571|<img src="img/imu-rot-6.png" width="180">|`IMU_ROT_ROLL` = 3.142<br>`IMU_ROT_PITCH` = 0<br>`IMU_ROT_YAW` = -1.571|
-|<img src="img/imu-rot-3.png" width="180">|`IMU_ROT_ROLL` = 0<br>`IMU_ROT_PITCH` = 0<br>`IMU_ROT_YAW` = 3.142|<img src="img/imu-rot-7.png" width="180">|`IMU_ROT_ROLL` = 3.142<br>`IMU_ROT_PITCH` = 0<br>`IMU_ROT_YAW` = 3.142|
-|<img src="img/imu-rot-4.png" width="180"><br>☑️ **Default**|<br>`IMU_ROT_ROLL` = 0<br>`IMU_ROT_PITCH` = 0<br>`IMU_ROT_YAW` = -1.571|<img src="img/imu-rot-8.png" width="180">|`IMU_ROT_ROLL` = 3.142<br>`IMU_ROT_PITCH` = 0<br>`IMU_ROT_YAW` = 1.571|
-
 ### Calibrate accelerometer
 
 Before flight you need to calibrate the accelerometer:
@@ -154,10 +136,6 @@ Before flight you need to calibrate the accelerometer:
    * `mrl` — should rotate rear left motor (counter-clockwise).
    * `mrr` — should rotate rear right motor (clockwise).
 
-   Rotation diagram:
-
-   <img src="img/motors.svg" width=200>
-
 > [!WARNING]
 > Never run the motors when powering the drone from USB, always use the battery for that.
 
@@ -165,7 +143,7 @@ Before flight you need to calibrate the accelerometer:
 
 There are several ways to control the drone's flight: using **smartphone** (Wi-Fi), using **SBUS remote control**, or using **USB remote control** (Wi-Fi).
 
-### Control with a smartphone
+### Control with smartphone
 
 1. Install [QGroundControl mobile app](https://docs.qgroundcontrol.com/master/en/qgc-user-guide/getting_started/download_and_install.html#android) on your smartphone.
 2. Power the drone using the battery.
@@ -175,9 +153,9 @@ There are several ways to control the drone's flight: using **smartphone** (Wi-F
 6. Use the virtual joystick to fly the drone!
 
 > [!TIP]
-> Decrease `CTL_TILT_MAX` parameter when flying using the smartphone to make the controls less sensitive.
+> Decrease `CNT_TILT_MAX` parameter when flying using the smartphone to make the controls less sensitive.
 
-### Control with a remote control
+### Control with remote control
 
 Before using remote SBUS-connected remote control, you need to calibrate it:
 
@@ -185,7 +163,7 @@ Before using remote SBUS-connected remote control, you need to calibrate it:
 2. Type `cr` command and follow the instructions.
 3. Use the remote control to fly the drone!
 
-### Control with a USB remote control
+### Control with USB remote control
 
 If your drone doesn't have RC receiver installed, you can use USB remote control and QGroundControl app to fly it.
 
@@ -233,9 +211,9 @@ The default mode is *STAB*. In this mode, the drone stabilizes its attitude (ori
 
 In this mode, the pilot controls the angular rates. This control method is difficult to fly and mostly used in FPV racing.
 
-#### RAW
+#### MANUAL
 
-*RAW* mode disables all the stabilization, and the pilot inputs are mixed directly to the motors. The IMU sensor is not involved. This mode is intended for testing and demonstration purposes only, and basically the drone **cannot fly in this mode**.
+Manual mode disables all the stabilization, and the pilot inputs are passed directly to the motors. This mode is intended for testing and demonstration purposes only, and basically the drone **cannot fly in this mode**.
 
 #### AUTO
 
@@ -243,6 +221,12 @@ In this mode, the pilot inputs are ignored (except the mode switch, if configure
 
 If the pilot moves the control sticks, the drone will switch back to *STAB* mode.
 
+## Adjusting parameters
+
+You can adjust some of the drone's parameters (include PID coefficients) in QGroundControl. In order to do that, go to the QGroundControl menu ⇒ *Vehicle Setup* ⇒ *Parameters*.
+
+<img src="img/parameters.png" width="400">
+
 ## Flight log
 
 After the flight, you can download the flight log for analysis wirelessly. Use the following for that:

docs/user.md

@@ -4,67 +4,12 @@ This page contains user-built drones based on the Flix project. Publish your pro
 
 ---
 
-Author: [goldarte](https://t.me/goldarte).<br>
-
-<img src="img/user/goldarte/1.jpg" height=150> <img src="img/user/goldarte/2.jpg" height=150>
-
-**Flight video:**
-
-<a href="https://drive.google.com/file/d/1nQtFjEcGGLx-l4xkL5ko9ZpOTVU-WDjL/view?usp=sharing"><img height=200 src="img/user/goldarte/video.jpg"></a>
-
----
-
-## School 548 course
-
-Special course on quadcopter design and engineering took place in october-november 2025 in School 548, Moscow. The course included UAV control theory, electronics, drone assembly and setup practice, using the Flix project.
-
-<img height=200 src="img/user/school548/1.jpg"> <img height=200 src="img/user/school548/2.jpg"> <img height=200 src="img/user/school548/3.jpg">
-
-STL files and other materials: see [here](https://drive.google.com/drive/folders/1wTUzj087LjKQQl3Lz5CjHCuobxoykhyp?usp=share_link).
-
-### Selected works
-
-Author: [KiraFlux](https://t.me/@kiraflux_0XC0000005).<br>
-Description: **custom ESPNOW remote control** was implemented, modified firmware to support ESPNOW protocol.<br>
-Telegram posts: [1](https://t.me/opensourcequadcopter/106), [2](https://t.me/opensourcequadcopter/114).<br>
-Modified Flix firmware: https://github.com/KiraFlux/flix/tree/klyax.<br>
-Remote control project: https://github.com/KiraFlux/ESP32-DJC.<br>
-Drone design: https://github.com/KiraFlux/Klyax.<br>
-
-<img src="img/user/school548/kiraflux1.jpg" height=150> <img src="img/user/school548/kiraflux2.jpg" height=150>
-
-**ESPNOW remote control demonstration**:
-
-<img height=200 src="img/user/school548/kiraflux-video.jpg"><a href="https://drive.google.com/file/d/1soHDAeHQWnm97Y4dg4nWevJuMiTdJJXW/view?usp=sharing"></a>
-
-Author: [tolyan4krut](https://t.me/tolyan4krut).<br>
-Description: the first drone based on ESP32-S3-CAM board **with a camera**, implementing Wi-Fi video streaming. Runs HTTP server and HTTP video stream.<br>
-Modified Flix firmware: https://github.com/CatRey/Flix-Camera-Streaming.<br>
-[Telegram post](https://t.me/opensourcequadcopter/117).
-
-<img src="img/user/school548/tolyan4krut.jpg" height=150>
-
-**Video streaming and flight demonstration**:
-
-<a href="https://drive.google.com/file/d/1KuOBsujLsk7q8FoqKD8u7uoq4ptS5onp/view?usp=sharing"><img height=200 src="img/user/school548/tolyan4krut-video.jpg"></a>
-
-Author: [Vlad Tolshinov](https://t.me/Vlad_Tolshinov).<br>
-Description: custom frame with enlarged arm length, which provides very high flight stability, 65 mm props.
-
-<img src="img/user/school548/vlad_tolshinov1.jpg" height=150> <img src="img/user/school548/vlad_tolshinov2.jpg" height=150>
-
-**Flight video**:
-
-<a href="https://drive.google.com/file/d/1zu00DZxhC7DJ9Z2mYjtxdNQqOOLAyYbp/view?usp=sharing"><img height=200 src="img/user/school548/vlad_tolshinov-video.jpg"></a>
-
----
-
 ## RoboCamp
 
 Author: RoboCamp participants.<br>
 Description: 3D-printed and wooden frames, ESP32 Mini, DC-DC buck-boost converters. BetaFPV LiteRadio 3 to control the drones via Wi-Fi connection.<br>
 Features: altitude hold, obstacle avoidance, autonomous flight elements.<br>
-Some of the designed model files: see [here](https://drive.google.com/drive/folders/18YHWGquKeIevzrMH4-OUT-zKXMETTEUu?usp=share_link).
+Some of the designed model files: https://drive.google.com/drive/folders/18YHWGquKeIevzrMH4-OUT-zKXMETTEUu?usp=share_link.
 
 RoboCamp took place in July 2025, Saint Petersburg, where 9 participants designed and built their own drones using the Flix project, and then modified the firmware to complete specific flight tasks.
 

flix/cli.ino

@@ -3,17 +3,15 @@
 
 // Implementation of command line interface
 
-#include <Arduino.h>
-#include "flix.h"
 #include "pid.h"
 #include "vector.h"
 #include "util.h"
 
 extern const int MOTOR_REAR_LEFT, MOTOR_REAR_RIGHT, MOTOR_FRONT_RIGHT, MOTOR_FRONT_LEFT;
-extern const int RAW, ACRO, STAB, AUTO;
+extern const int ACRO, STAB, AUTO;
 extern float t, dt, loopRate;
 extern uint16_t channels[16];
-extern float controlTime;
+extern float controlRoll, controlPitch, controlThrottle, controlYaw, controlMode;
 extern int mode;
 extern bool armed;
 
@@ -37,9 +35,8 @@ const char* motd =
 "imu - show IMU data\n"
 "arm - arm the drone\n"
 "disarm - disarm the drone\n"
-"raw/stab/acro/auto - set mode\n"
+"stab/acro/auto - set mode\n"
 "rc - show RC data\n"
-"wifi - show Wi-Fi info\n"
 "mot - show motor output\n"
 "log [dump] - print log header [and data]\n"
 "cr - calibrate RC\n"
@@ -73,7 +70,7 @@ void pause(float duration) {
 	}
 }
 
-void doCommand(String str, bool echo) {
+void doCommand(String str, bool echo = false) {
 	// parse command
 	String command, arg0, arg1;
 	splitString(str, command, arg0, arg1);
@@ -119,8 +116,6 @@ void doCommand(String str, bool echo) {
 		armed = true;
 	} else if (command == "disarm") {
 		armed = false;
-	} else if (command == "raw") {
-		mode = RAW;
 	} else if (command == "stab") {
 		mode = STAB;
 	} else if (command == "acro") {
@@ -134,13 +129,8 @@ void doCommand(String str, bool echo) {
 		}
 		print("\nroll: %g pitch: %g yaw: %g throttle: %g mode: %g\n",
 			controlRoll, controlPitch, controlYaw, controlThrottle, controlMode);
-		print("time: %.1f\n", controlTime);
 		print("mode: %s\n", getModeName());
 		print("armed: %d\n", armed);
-	} else if (command == "wifi") {
-#if WIFI_ENABLED
-		printWiFiInfo();
-#endif
 	} else if (command == "mot") {
 		print("front-right %g front-left %g rear-right %g rear-left %g\n",
 			motors[MOTOR_FRONT_RIGHT], motors[MOTOR_FRONT_LEFT], motors[MOTOR_REAR_RIGHT], motors[MOTOR_REAR_LEFT]);

flix/config.h

@@ -1,55 +0,0 @@
-// Wi-Fi
-#define WIFI_ENABLED 1
-#define WIFI_SSID "flix"
-#define WIFI_PASSWORD "flixwifi"
-#define WIFI_UDP_PORT 14550
-#define WIFI_UDP_REMOTE_PORT 14550
-#define WIFI_UDP_REMOTE_ADDR "255.255.255.255"
-
-// Motors
-#define MOTOR_0_PIN 12 // rear left
-#define MOTOR_1_PIN 13 // rear right
-#define MOTOR_2_PIN 14 // front right
-#define MOTOR_3_PIN 15 // front left
-#define PWM_FREQUENCY 78000
-#define PWM_RESOLUTION 10
-#define PWM_STOP 0
-#define PWM_MIN 0
-#define PWM_MAX 1000000 / PWM_FREQUENCY
-
-// Control
-#define PITCHRATE_P 0.05
-#define PITCHRATE_I 0.2
-#define PITCHRATE_D 0.001
-#define PITCHRATE_I_LIM 0.3
-#define ROLLRATE_P PITCHRATE_P
-#define ROLLRATE_I PITCHRATE_I
-#define ROLLRATE_D PITCHRATE_D
-#define ROLLRATE_I_LIM PITCHRATE_I_LIM
-#define YAWRATE_P 0.3
-#define YAWRATE_I 0.0
-#define YAWRATE_D 0.0
-#define YAWRATE_I_LIM 0.3
-#define ROLL_P 6
-#define ROLL_I 0
-#define ROLL_D 0
-#define PITCH_P ROLL_P
-#define PITCH_I ROLL_I
-#define PITCH_D ROLL_D
-#define YAW_P 3
-#define PITCHRATE_MAX radians(360)
-#define ROLLRATE_MAX radians(360)
-#define YAWRATE_MAX radians(300)
-#define TILT_MAX radians(30)
-#define RATES_D_LPF_ALPHA 0.2 // cutoff frequency ~ 40 Hz
-
-// Estimation
-#define WEIGHT_ACC 0.003
-#define RATES_LFP_ALPHA 0.2 // cutoff frequency ~ 40 Hz
-
-// MAVLink
-#define SYSTEM_ID 1
-
-// Safety
-#define RC_LOSS_TIMEOUT 1
-#define DESCEND_TIME 10

flix/control.ino

@@ -3,25 +3,41 @@
 
 // Flight control
 
-#include "config.h"
-#include "flix.h"
 #include "vector.h"
 #include "quaternion.h"
 #include "pid.h"
 #include "lpf.h"
 #include "util.h"
 
-extern const int RAW = 0, ACRO = 1, STAB = 2, AUTO = 3; // flight modes
+#define PITCHRATE_P 0.05
+#define PITCHRATE_I 0.2
+#define PITCHRATE_D 0.001
+#define PITCHRATE_I_LIM 0.3
+#define ROLLRATE_P PITCHRATE_P
+#define ROLLRATE_I PITCHRATE_I
+#define ROLLRATE_D PITCHRATE_D
+#define ROLLRATE_I_LIM PITCHRATE_I_LIM
+#define YAWRATE_P 0.3
+#define YAWRATE_I 0.0
+#define YAWRATE_D 0.0
+#define YAWRATE_I_LIM 0.3
+#define ROLL_P 6
+#define ROLL_I 0
+#define ROLL_D 0
+#define PITCH_P ROLL_P
+#define PITCH_I ROLL_I
+#define PITCH_D ROLL_D
+#define YAW_P 3
+#define PITCHRATE_MAX radians(360)
+#define ROLLRATE_MAX radians(360)
+#define YAWRATE_MAX radians(300)
+#define TILT_MAX radians(30)
+#define RATES_D_LPF_ALPHA 0.2 // cutoff frequency ~ 40 Hz
 
+const int MANUAL = 0, ACRO = 1, STAB = 2, AUTO = 3; // flight modes
 int mode = STAB;
 bool armed = false;
 
-Quaternion attitudeTarget;
-Vector ratesTarget;
-Vector ratesExtra; // feedforward rates
-Vector torqueTarget;
-float thrustTarget;
-
 PID rollRatePID(ROLLRATE_P, ROLLRATE_I, ROLLRATE_D, ROLLRATE_I_LIM, RATES_D_LPF_ALPHA);
 PID pitchRatePID(PITCHRATE_P, PITCHRATE_I, PITCHRATE_D, PITCHRATE_I_LIM, RATES_D_LPF_ALPHA);
 PID yawRatePID(YAWRATE_P, YAWRATE_I, YAWRATE_D);
@@ -31,6 +47,12 @@ PID yawPID(YAW_P, 0, 0);
 Vector maxRate(ROLLRATE_MAX, PITCHRATE_MAX, YAWRATE_MAX);
 float tiltMax = TILT_MAX;
 
+Quaternion attitudeTarget;
+Vector ratesTarget;
+Vector ratesExtra; // feedforward rates
+Vector torqueTarget;
+float thrustTarget;
+
 extern const int MOTOR_REAR_LEFT, MOTOR_REAR_RIGHT, MOTOR_FRONT_RIGHT, MOTOR_FRONT_LEFT;
 extern float controlRoll, controlPitch, controlThrottle, controlYaw, controlMode;
 
@@ -43,6 +65,7 @@ void control() {
 }
 
 void interpretControls() {
+	// NOTE: put ACRO or MANUAL modes there if you want to use them
 	if (controlMode < 0.25) mode = STAB;
 	if (controlMode < 0.75) mode = STAB;
 	if (controlMode > 0.75) mode = STAB;
@@ -52,8 +75,6 @@ void interpretControls() {
 	if (controlThrottle < 0.05 && controlYaw > 0.95) armed = true; // arm gesture
 	if (controlThrottle < 0.05 && controlYaw < -0.95) armed = false; // disarm gesture
 
-	if (abs(controlYaw) < 0.1) controlYaw = 0; // yaw dead zone
-
 	thrustTarget = controlThrottle;
 
 	if (mode == STAB) {
@@ -70,10 +91,10 @@ void interpretControls() {
 		ratesTarget.z = -controlYaw * maxRate.z; // positive yaw stick means clockwise rotation in FLU
 	}
 
-	if (mode == RAW) { // direct torque control
+	if (mode == MANUAL) { // passthrough mode
 		attitudeTarget.invalidate(); // skip attitude control
 		ratesTarget.invalidate(); // skip rate control
-		torqueTarget = Vector(controlRoll, controlPitch, -controlYaw) * 0.1;
+		torqueTarget = Vector(controlRoll, controlPitch, -controlYaw) * 0.01;
 	}
 }
 
@@ -134,7 +155,7 @@ void controlTorque() {
 
 const char* getModeName() {
 	switch (mode) {
-		case RAW: return "RAW";
+		case MANUAL: return "MANUAL";
 		case ACRO: return "ACRO";
 		case STAB: return "STAB";
 		case AUTO: return "AUTO";

flix/estimate.ino

@@ -3,19 +3,13 @@
 
 // Attitude estimation from gyro and accelerometer
 
-#include "config.h"
-#include "flix.h"
 #include "quaternion.h"
 #include "vector.h"
 #include "lpf.h"
 #include "util.h"
 
-Vector rates; // estimated angular rates, rad/s
-Quaternion attitude; // estimated attitude
-bool landed;
-
-float accWeight = 0.003;
-LowPassFilter<Vector> ratesFilter(0.2); // cutoff frequency ~ 40 Hz
+#define WEIGHT_ACC 0.003
+#define RATES_LFP_ALPHA 0.2 // cutoff frequency ~ 40 Hz
 
 void estimate() {
 	applyGyro();
@@ -24,6 +18,7 @@ void estimate() {
 
 void applyGyro() {
 	// filter gyro to get angular rates
+	static LowPassFilter<Vector> ratesFilter(RATES_LFP_ALPHA);
 	rates = ratesFilter.update(gyro);
 
 	// apply rates to attitude
@@ -39,7 +34,7 @@ void applyAcc() {
 
 	// calculate accelerometer correction
 	Vector up = Quaternion::rotateVector(Vector(0, 0, 1), attitude);
-	Vector correction = Vector::rotationVectorBetween(acc, up) * accWeight;
+	Vector correction = Vector::rotationVectorBetween(acc, up) * WEIGHT_ACC;
 
 	// apply correction
 	attitude = Quaternion::rotate(attitude, Quaternion::fromRotationVector(correction));

flix/flix.h

@@ -1,90 +0,0 @@
-// Copyright (c) 2023 Oleg Kalachev <okalachev@gmail.com>
-// Repository: https://github.com/okalachev/flix
-
-// All-in-one header file
-
-#pragma once
-
-#include <Arduino.h>
-#include "vector.h"
-#include "quaternion.h"
-
-extern float t, dt;
-extern float loopRate;
-extern float controlRoll, controlPitch, controlYaw, controlThrottle, controlMode;
-extern Vector gyro, acc;
-extern Vector rates;
-extern Quaternion attitude;
-extern bool landed;
-extern int mode;
-extern bool armed;
-extern Quaternion attitudeTarget;
-extern Vector ratesTarget, ratesExtra, torqueTarget;
-extern float thrustTarget;
-extern float motors[4];
-
-void print(const char* format, ...);
-void pause(float duration);
-void doCommand(String str, bool echo = false);
-void handleInput();
-void control();
-void interpretControls();
-void controlAttitude();
-void controlRates();
-void controlTorque();
-const char *getModeName();
-void estimate();
-void applyGyro();
-void applyAcc();
-void setupIMU();
-void configureIMU();
-void readIMU();
-void rotateIMU(Vector& data);
-void calibrateGyroOnce();
-void calibrateAccel();
-void calibrateAccelOnce();
-void printIMUCalibration();
-void printIMUInfo();
-void setupLED();
-void setLED(bool on);
-void blinkLED();
-void prepareLogData();
-void logData();
-void printLogHeader();
-void printLogData();
-void processMavlink();
-void sendMavlink();
-void sendMessage(const void *msg);
-void receiveMavlink();
-void handleMavlink(const void *_msg);
-void mavlinkPrint(const char* str);
-void sendMavlinkPrint();
-void setupMotors();
-int getDutyCycle(float value);
-void sendMotors();
-bool motorsActive();
-void testMotor(int n);
-void setupParameters();
-int parametersCount();
-const char *getParameterName(int index);
-float getParameter(int index);
-float getParameter(const char *name);
-bool setParameter(const char *name, const float value);
-void syncParameters();
-void printParameters();
-void resetParameters();
-void setupRC();
-bool readRC();
-void normalizeRC();
-void calibrateRC();
-void calibrateRCChannel(float *channel, uint16_t in[16], uint16_t out[16], const char *str);
-void printRCCalibration();
-void failsafe();
-void rcLossFailsafe();
-void descend();
-void autoFailsafe();
-void step();
-void computeLoopRate();
-void setupWiFi();
-void sendWiFi(const uint8_t *buf, int len);
-int receiveWiFi(uint8_t *buf, int len);

flix/flix.ino

@@ -3,11 +3,22 @@
 
 // Main firmware file
 
-#include "config.h"
 #include "vector.h"
 #include "quaternion.h"
 #include "util.h"
-#include "flix.h"
+
+#define WIFI_ENABLED 1
+
+float t = NAN; // current step time, s
+float dt; // time delta from previous step, s
+float controlRoll, controlPitch, controlYaw, controlThrottle; // pilot's inputs, range [-1, 1]
+float controlMode = NAN;
+Vector gyro; // gyroscope data
+Vector acc; // accelerometer data, m/s/s
+Vector rates; // filtered angular rates, rad/s
+Quaternion attitude; // estimated attitude
+bool landed; // are we landed and stationary
+float motors[4]; // normalized motors thrust in range [0..1]
 
 void setup() {
 	Serial.begin(115200);

flix/imu.ino

@@ -10,14 +10,10 @@
 #include "util.h"
 
 MPU9250 imu(SPI);
-Vector imuRotation(0, 0, -PI / 2); // imu orientation as Euler angles
 
-Vector gyro; // gyroscope output, rad/s
-Vector gyroBias;
-
-Vector acc; // accelerometer output, m/s/s
 Vector accBias;
 Vector accScale(1, 1, 1);
+Vector gyroBias;
 
 void setupIMU() {
 	print("Setup IMU\n");
@@ -41,18 +37,24 @@ void readIMU() {
 	// apply scale and bias
 	acc = (acc - accBias) / accScale;
 	gyro = gyro - gyroBias;
-	// rotate to body frame
-	Quaternion rotation = Quaternion::fromEuler(imuRotation);
-	acc = Quaternion::rotateVector(acc, rotation.inversed());
-	gyro = Quaternion::rotateVector(gyro, rotation.inversed());
+	// rotate
+	rotateIMU(acc);
+	rotateIMU(gyro);
+}
+
+void rotateIMU(Vector& data) {
+	// Rotate from LFD to FLU
+	// NOTE: In case of using other IMU orientation, change this line:
+	data = Vector(data.y, data.x, -data.z);
+	// Axes orientation for various boards: https://github.com/okalachev/flixperiph#imu-axes-orientation
 }
 
 void calibrateGyroOnce() {
 	static Delay landedDelay(2);
 	if (!landedDelay.update(landed)) return; // calibrate only if definitely stationary
 
-	static LowPassFilter<Vector> gyroBiasFilter(0.001);
-	gyroBias = gyroBiasFilter.update(gyro);
+	static LowPassFilter<Vector> gyroCalibrationFilter(0.001);
+	gyroBias = gyroCalibrationFilter.update(gyro);
 }
 
 void calibrateAccel() {

flix/led.ino

@@ -3,8 +3,6 @@
 
 // Board's LED control
 
-#include <Arduino.h>
-
 #define BLINK_PERIOD 500000
 
 #ifndef LED_BUILTIN

flix/log.ino

@@ -3,7 +3,6 @@
 
 // In-RAM logging
 
-#include "flix.h"
 #include "vector.h"
 #include "util.h"
 

flix/lpf.h

@@ -5,8 +5,6 @@
 
 #pragma once
 
-#include <Arduino.h>
-
 template <typename T> // Using template to make the filter usable for scalar and vector values
 class LowPassFilter {
 public:

flix/mavlink.ino

@@ -3,10 +3,6 @@
 
 // MAVLink communication
 
-#include <Arduino.h>
-#include "config.h"
-#include "flix.h"
-
 #if WIFI_ENABLED
 
 #include <MAVLink.h>
@@ -15,14 +11,14 @@
 #define SYSTEM_ID 1
 #define MAVLINK_RATE_SLOW 1
 #define MAVLINK_RATE_FAST 10
-
-extern const int AUTO, STAB;
-extern uint16_t channels[16];
-extern float controlTime;
+#define MAVLINK_CONTROL_YAW_DEAD_ZONE 0.1f
 
 bool mavlinkConnected = false;
 String mavlinkPrintBuffer;
 
+extern float controlTime;
+extern float controlRoll, controlPitch, controlThrottle, controlYaw, controlMode;
+
 void processMavlink() {
 	sendMavlink();
 	receiveMavlink();
@@ -109,6 +105,8 @@ void handleMavlink(const void *_msg) {
 		controlYaw = m.r / 1000.0f;
 		controlMode = NAN;
 		controlTime = t;
+
+		if (abs(controlYaw) < MAVLINK_CONTROL_YAW_DEAD_ZONE) controlYaw = 0;
 	}
 
 	if (msg.msgid == MAVLINK_MSG_ID_PARAM_REQUEST_LIST) {
@@ -212,7 +210,6 @@ void handleMavlink(const void *_msg) {
 		armed = motors[0] > 0 || motors[1] > 0 || motors[2] > 0 || motors[3] > 0;
 	}
 
-	/* TODO:
 	if (msg.msgid == MAVLINK_MSG_ID_LOG_REQUEST_DATA) {
 		mavlink_log_request_data_t m;
 		mavlink_msg_log_request_data_decode(&msg, &m);
@@ -226,7 +223,6 @@ void handleMavlink(const void *_msg) {
 			sendMessage(&msg);
 		}
 	}
-	*/
 
 	// Handle commands
 	if (msg.msgid == MAVLINK_MSG_ID_COMMAND_LONG) {

flix/motors.ino

@@ -4,17 +4,24 @@
 // Motors output control using MOSFETs
 // In case of using ESCs, change PWM_STOP, PWM_MIN and PWM_MAX to appropriate values in μs, decrease PWM_FREQUENCY (to 400)
 
-#include <Arduino.h>
-#include "config.h"
-#include "flix.h"
 #include "util.h"
 
-float motors[4]; // normalized motor thrusts in range [0..1]
+#define MOTOR_0_PIN 12 // rear left
+#define MOTOR_1_PIN 13 // rear right
+#define MOTOR_2_PIN 14 // front right
+#define MOTOR_3_PIN 15 // front left
 
-extern const int MOTOR_REAR_LEFT = 0;
-extern const int MOTOR_REAR_RIGHT = 1;
-extern const int MOTOR_FRONT_RIGHT = 2;
-extern const int MOTOR_FRONT_LEFT = 3;
+#define PWM_FREQUENCY 78000
+#define PWM_RESOLUTION 10
+#define PWM_STOP 0
+#define PWM_MIN 0
+#define PWM_MAX 1000000 / PWM_FREQUENCY
+
+// Motors array indexes:
+const int MOTOR_REAR_LEFT = 0;
+const int MOTOR_REAR_RIGHT = 1;
+const int MOTOR_FRONT_RIGHT = 2;
+const int MOTOR_FRONT_LEFT = 3;
 
 void setupMotors() {
 	print("Setup Motors\n");

flix/parameters.ino

@@ -4,22 +4,11 @@
 // Parameters storage in flash memory
 
 #include <Preferences.h>
-#include "flix.h"
-#include "pid.h"
-#include "lpf.h"
 #include "util.h"
 
 extern float channelZero[16];
 extern float channelMax[16];
 extern float rollChannel, pitchChannel, throttleChannel, yawChannel, armedChannel, modeChannel;
-extern float tiltMax;
-extern PID rollPID, pitchPID, yawPID;
-extern PID rollRatePID, pitchRatePID, yawRatePID;
-extern Vector maxRate;
-extern Vector imuRotation;
-extern Vector accBias, accScale;
-extern float accWeight;
-extern LowPassFilter<Vector> ratesFilter;
 
 Preferences storage;
 
@@ -54,18 +43,12 @@ Parameter parameters[] = {
 	{"CTL_Y_RATE_MAX", &maxRate.z},
 	{"CTL_TILT_MAX", &tiltMax},
 	// imu
-	{"IMU_ROT_ROLL", &imuRotation.x},
-	{"IMU_ROT_PITCH", &imuRotation.y},
-	{"IMU_ROT_YAW", &imuRotation.z},
 	{"IMU_ACC_BIAS_X", &accBias.x},
 	{"IMU_ACC_BIAS_Y", &accBias.y},
 	{"IMU_ACC_BIAS_Z", &accBias.z},
 	{"IMU_ACC_SCALE_X", &accScale.x},
 	{"IMU_ACC_SCALE_Y", &accScale.y},
 	{"IMU_ACC_SCALE_Z", &accScale.z},
-	// estimate
-	{"EST_ACC_WEIGHT", &accWeight},
-	{"EST_RATES_LPF_A", &ratesFilter.alpha},
 	// rc
 	{"RC_ZERO_0", &channelZero[0]},
 	{"RC_ZERO_1", &channelZero[1]},

flix/pid.h

@@ -5,8 +5,6 @@
 
 #pragma once
 
-#include "Arduino.h"
-#include "flix.h"
 #include "lpf.h"
 
 class PID {

flix/quaternion.h

@@ -5,7 +5,6 @@
 
 #pragma once
 
-#include <Arduino.h>
 #include "vector.h"
 
 class Quaternion : public Printable {

flix/rc.ino

@@ -6,16 +6,13 @@
 #include <SBUS.h>
 #include "util.h"
 
-SBUS rc(Serial2);
+SBUS rc(Serial2); // NOTE: Use RC(Serial2, 16, 17) if you use the old UART2 pins
 
 uint16_t channels[16]; // raw rc channels
+float controlTime; // time of the last controls update
 float channelZero[16]; // calibration zero values
 float channelMax[16]; // calibration max values
 
-float controlRoll, controlPitch, controlYaw, controlThrottle; // pilot's inputs, range [-1, 1]
-float controlMode = NAN; //
-float controlTime; // time of the last controls update (0 when no RC)
-
 // Channels mapping (using float to store in parameters):
 float rollChannel = NAN, pitchChannel = NAN, throttleChannel = NAN, yawChannel = NAN, modeChannel = NAN;
 
@@ -41,11 +38,11 @@ void normalizeRC() {
 		controls[i] = mapf(channels[i], channelZero[i], channelMax[i], 0, 1);
 	}
 	// Update control values
-	controlRoll = rollChannel >= 0 ? controls[(int)rollChannel] : 0;
-	controlPitch = pitchChannel >= 0 ? controls[(int)pitchChannel] : 0;
-	controlYaw = yawChannel >= 0 ? controls[(int)yawChannel] : 0;
-	controlThrottle = throttleChannel >= 0 ? controls[(int)throttleChannel] : 0;
-	controlMode = modeChannel >= 0 ? controls[(int)modeChannel] : NAN; // mode switch should not have affect if not set
+	controlRoll = rollChannel >= 0 ? controls[(int)rollChannel] : NAN;
+	controlPitch = pitchChannel >= 0 ? controls[(int)pitchChannel] : NAN;
+	controlYaw = yawChannel >= 0 ? controls[(int)yawChannel] : NAN;
+	controlThrottle = throttleChannel >= 0 ? controls[(int)throttleChannel] : NAN;
+	controlMode = modeChannel >= 0 ? controls[(int)modeChannel] : NAN;
 }
 
 void calibrateRC() {

flix/safety.ino

@@ -3,11 +3,11 @@
 
 // Fail-safe functions
 
-#include "config.h"
-#include "flix.h"
+#define RC_LOSS_TIMEOUT 1
+#define DESCEND_TIME 10
 
 extern float controlTime;
-extern const int AUTO, STAB;
+extern float controlRoll, controlPitch, controlThrottle, controlYaw;
 
 void failsafe() {
 	rcLossFailsafe();

flix/time.ino

@@ -3,11 +3,6 @@
 
 // Time related functions
 
-#include "Arduino.h"
-#include "flix.h"
-
-float t = NAN; // current time, s
-float dt; // time delta with the previous step, s
 float loopRate; // Hz
 
 void step() {

flix/util.h

@@ -8,24 +8,24 @@
 #include <math.h>
 #include <soc/soc.h>
 #include <soc/rtc_cntl_reg.h>
-#include "flix.h"
 
 const float ONE_G = 9.80665;
+extern float t;
 
-inline float mapf(float x, float in_min, float in_max, float out_min, float out_max) {
+float mapf(float x, float in_min, float in_max, float out_min, float out_max) {
 	return (x - in_min) * (out_max - out_min) / (in_max - in_min) + out_min;
 }
 
-inline bool invalid(float x) {
+bool invalid(float x) {
 	return !isfinite(x);
 }
 
-inline bool valid(float x) {
+bool valid(float x) {
 	return isfinite(x);
 }
 
 // Wrap angle to [-PI, PI)
-inline float wrapAngle(float angle) {
+float wrapAngle(float angle) {
 	angle = fmodf(angle, 2 * PI);
 	if (angle > PI) {
 		angle -= 2 * PI;
@@ -36,12 +36,12 @@ inline float wrapAngle(float angle) {
 }
 
 // Disable reset on low voltage
-inline void disableBrownOut() {
+void disableBrownOut() {
 	REG_CLR_BIT(RTC_CNTL_BROWN_OUT_REG, RTC_CNTL_BROWN_OUT_ENA);
 }
 
 // Trim and split string by spaces
-inline void splitString(String& str, String& token0, String& token1, String& token2) {
+void splitString(String& str, String& token0, String& token1, String& token2) {
 	str.trim();
 	char chars[str.length() + 1];
 	str.toCharArray(chars, str.length() + 1);

flix/vector.h

@@ -5,8 +5,6 @@
 
 #pragma once
 
-#include <Arduino.h>
-
 class Vector : public Printable {
 public:
 	float x, y, z;
@@ -37,6 +35,7 @@ public:
 		z = NAN;
 	}
 
+
 	float norm() const {
 		return sqrt(x * x + y * y + z * z);
 	}
@@ -125,5 +124,5 @@ public:
 	}
 };
 
-inline Vector operator * (const float a, const Vector& b) { return b * a; }
-inline Vector operator + (const float a, const Vector& b) { return b + a; }
+Vector operator * (const float a, const Vector& b) { return b * a; }
+Vector operator + (const float a, const Vector& b) { return b + a; }

flix/wifi.ino

@@ -3,22 +3,30 @@
 
 // Wi-Fi support
 
-#include "config.h"
-#include "flix.h"
-
 #if WIFI_ENABLED
 
 #include <WiFi.h>
 #include <WiFiAP.h>
 #include <WiFiUdp.h>
 
-WiFiUDP udp;
+#define WIFI_AP_MODE 1
+#define WIFI_AP_SSID "flix"
+#define WIFI_AP_PASSWORD "flixwifi"
+#define WIFI_SSID ""
+#define WIFI_PASSWORD ""
+#define WIFI_UDP_PORT 14550
+#define WIFI_UDP_REMOTE_PORT 14550
+#define WIFI_UDP_REMOTE_ADDR "255.255.255.255"
 
-extern bool mavlinkConnected;
+WiFiUDP udp;
 
 void setupWiFi() {
 	print("Setup Wi-Fi\n");
-	WiFi.softAP(WIFI_SSID, WIFI_PASSWORD);
+	if (WIFI_AP_MODE) {
+		WiFi.softAP(WIFI_AP_SSID, WIFI_AP_PASSWORD);
+	} else {
+		WiFi.begin(WIFI_SSID, WIFI_PASSWORD);
+	}
 	udp.begin(WIFI_UDP_PORT);
 }
 
@@ -34,15 +42,4 @@ int receiveWiFi(uint8_t *buf, int len) {
 	return udp.read(buf, len);
 }
 
-void printWiFiInfo() {
-	print("MAC: %s\n", WiFi.softAPmacAddress().c_str());
-	print("SSID: %s\n", WiFi.softAPSSID().c_str());
-	print("Password: %s\n", WIFI_PASSWORD);
-	print("Clients: %d\n", WiFi.softAPgetStationNum());
-	print("Status: %d\n", WiFi.status());
-	print("IP: %s\n", WiFi.softAPIP().toString().c_str());
-	print("Remote IP: %s\n", udp.remoteIP().toString().c_str());
-	print("MAVLink connected: %d\n", mavlinkConnected);
-}
-
 #endif

gazebo/README.md

@@ -68,9 +68,6 @@ Just like the real drone, the simulator can be controlled using a USB remote con
 6. Go to the settings and enable *Virtual Joystick*. *Auto-Center Throttle* setting **should be disabled**.
 7. Use the virtual joystick to fly the drone!
 
-> [!TIP]
-> Decrease `CTL_TILT_MAX` parameter when flying using the smartphone to make the controls less sensitive.
-
 ### Control with USB remote control
 
 1. Connect your USB remote control to the machine running the simulator.

gazebo/flix.h

@@ -12,15 +12,16 @@
 
 #define WIFI_ENABLED 1
 
-extern float t, dt;
-extern float controlRoll, controlPitch, controlYaw, controlThrottle, controlMode;
-extern Vector rates;
-extern Quaternion attitude;
-extern bool landed;
-extern float motors[4];
-
-Vector gyro, acc, imuRotation;
-Vector accBias, gyroBias, accScale(1, 1, 1);
+float t = NAN;
+float dt;
+float motors[4];
+float controlRoll, controlPitch, controlYaw, controlThrottle = NAN;
+float controlMode = NAN;
+Vector acc;
+Vector gyro;
+Vector rates;
+Quaternion attitude;
+bool landed;
 
 // declarations
 void step();
@@ -72,4 +73,4 @@ void calibrateGyro() { print("Skip gyro calibrating\n"); };
 void calibrateAccel() { print("Skip accel calibrating\n"); };
 void printIMUCalibration() { print("cal: N/A\n"); };
 void printIMUInfo() {};
-void printWiFiInfo() {};
+Vector accBias, gyroBias, accScale(1, 1, 1);

tools/pyflix/README.md

@@ -1,8 +1,8 @@
 # Flix Python library
 
-The Flix Python library allows you to remotely connect to a Flix quadcopter. It provides access to telemetry data, supports executing console commands, and controlling the drone's flight.
+The Flix Python library allows you to remotely connect to a Flix quadcopter. It provides access to telemetry data, supports executing CLI commands, and controlling the drone's flight.
 
-To use the library, connect to the drone's Wi-Fi. To use it with the simulator, ensure the script runs on the same network as the simulator.
+To use the library, connect to the drone's Wi-Fi. To use it with the simulator, ensure the script runs on the same local network as the simulator.
 
 ## Installation
 
@@ -30,7 +30,7 @@ flix = Flix()  # create a Flix object and wait for connection
 
 ### Telemetry
 
-Basic telemetry is available through object properties. The property names generally match the corresponding variables in the firmware itself:
+Basic telemetry is available through object properties. The properties names generally match the corresponding variables in the firmware itself:
 
 ```python
 print(flix.connected)       # True if connected to the drone
@@ -41,7 +41,7 @@ print(flix.attitude)        # attitude quaternion [w, x, y, z]
 print(flix.attitude_euler)  # attitude as Euler angles [roll, pitch, yaw]
 print(flix.rates)           # angular rates [roll_rate, pitch_rate, yaw_rate]
 print(flix.channels)        # raw RC channels (list)
-print(flix.motors)          # motor outputs (list)
+print(flix.motors)          # motors outputs (list)
 print(flix.acc)             # accelerometer output (list)
 print(flix.gyro)            # gyroscope output (list)
 ```
@@ -95,24 +95,24 @@ Full list of events:
 |`armed`|Armed state update|Armed state (*bool*)|
 |`mode`|Flight mode update|Flight mode (*str*)|
 |`landed`|Landed state update|Landed state (*bool*)|
-|`print`|The drone prints text to the console|Text|
+|`print`|The drone sends text to the console|Text|
 |`attitude`|Attitude update|Attitude quaternion (*list*)|
 |`attitude_euler`|Attitude update|Euler angles (*list*)|
 |`rates`|Angular rates update|Angular rates (*list*)|
 |`channels`|Raw RC channels update|Raw RC channels (*list*)|
-|`motors`|Motor outputs update|Motor outputs (*list*)|
+|`motors`|Motors outputs update|Motors outputs (*list*)|
 |`acc`|Accelerometer update|Accelerometer output (*list*)|
 |`gyro`|Gyroscope update|Gyroscope output (*list*)|
 |`mavlink`|Received MAVLink message|Message object|
 |`mavlink.<message_name>`|Received specific MAVLink message|Message object|
 |`mavlink.<message_id>`|Received specific MAVLink message|Message object|
 |`value`|Named value update (see below)|Name, value|
-|`value.<name>`|Specific named value update (see below)|Value|
+|`value.<name>`|Specific named value update (see bellow)|Value|
 
 > [!NOTE]
-> Update events trigger on every new piece of data from the drone, and do not mean the value has changed.
+> Update events trigger on every new data from the drone, and do not mean the value has changed.
 
-### Basic methods
+### Common methods
 
 Get and set firmware parameters using `get_param` and `set_param` methods:
 
@@ -121,7 +121,7 @@ pitch_p = flix.get_param('PITCH_P')  # get parameter value
 flix.set_param('PITCH_P', 5)         # set parameter value
 ```
 
-Execute console commands using `cli` method. This method returns the command response:
+Execute console commands using `cli` method. This method returns command response:
 
 ```python
 imu = flix.cli('imu')    # get detailed IMU data
@@ -169,10 +169,10 @@ Setting angular rates target:
 flix.set_rates([0.1, 0.2, 0.3], 0.6)  # set target roll rate, pitch rate, yaw rate and thrust
 ```
 
-You also can control raw motor outputs directly:
+You also can control raw motors outputs directly:
 
 ```python
-flix.set_motors([0.5, 0.5, 0.5, 0.5])  # set motor outputs in range [0, 1]
+flix.set_motors([0.5, 0.5, 0.5, 0.5])  # set motors outputs in range [0, 1]
 ```
 
 In *AUTO* mode, the drone will arm automatically if the thrust is greater than zero, and disarm if thrust is zero. Therefore, to disarm the drone, set thrust to zero:
@@ -186,7 +186,7 @@ The following methods are in development and are not functional yet:
 * `set_position` — set target position.
 * `set_velocity` — set target velocity.
 
-To exit *AUTO* mode move control sticks and the drone will switch to *STAB* mode.
+To exit from *AUTO* mode move control sticks and the drone will switch to *STAB* mode.
 
 ## Usage alongside QGroundControl
 

tools/pyflix/flix.py

@@ -17,7 +17,7 @@ from pymavlink.dialects.v20 import common as mavlink
 logger = logging.getLogger('flix')
 if not logger.hasHandlers():
     handler = logging.StreamHandler()
-    handler.setFormatter(logging.Formatter('%(name)s: %(message)s'))
+    handler.setFormatter(logging.Formatter('%(name)s - %(levelname)s - %(message)s'))
     logger.addHandler(handler)
     logger.setLevel(logging.INFO)
 
@@ -40,7 +40,7 @@ class Flix:
 
     _connection_timeout = 3
     _print_buffer: str = ''
-    _modes = ['RAW', 'ACRO', 'STAB', 'AUTO']
+    _modes = ['MANUAL', 'ACRO', 'STAB', 'AUTO']
 
     def __init__(self, system_id: int=1, wait_connection: bool=True):
         if not (0 <= system_id < 256):

tools/pyproject.toml

@@ -1,6 +1,6 @@
 [project]
 name = "pyflix"
-version = "0.11"
+version = "0.9"
 description = "Python API for Flix drone"
 authors = [{ name="Oleg Kalachev", email="okalachev@gmail.com" }]
 license = "MIT"