Update ESP32-Core to 3.3.6

Update MAVLink-Arduino to 2.0.16
Make failsafe configurable using parameters
2026-03-30 03:54:20 +00:00 · 2026-01-23 02:41:43 +03:00 · 2026-01-23 01:11:35 +03:00 · 2026-01-22 23:57:52 +03:00 · 2026-01-22 23:11:47 +03:00 · 2026-01-22 23:04:45 +03:00
55 changed files with 473 additions and 278 deletions
--- a/.github/workflows/build.yml
+++ b/.github/workflows/build.yml
@@ -25,8 +25,6 @@ jobs:
        path: flix/build
    - name: Build firmware for ESP32-S3
      run: make BOARD=esp32:esp32:esp32s3
-    - name: Build firmware with WiFi disabled
-      run: sed -i 's/^#define WIFI_ENABLED 1$/#define WIFI_ENABLED 0/' flix/flix.ino && make
    - name: Check c_cpp_properties.json
      run: tools/check_c_cpp_properties.py

--- a/.github/workflows/tools.yml
+++ b/.github/workflows/tools.yml
@@ -46,14 +46,3 @@ jobs:
        echo -e "t,x,y,z\n0,1,2,3\n1,4,5,6" > log.csv
        ./csv_to_mcap.py log.csv
        test $(stat -c %s log.mcap) -eq 883
-
-  sloc:
-    runs-on: ubuntu-latest
-    steps:
-    - uses: actions/checkout@v4
-    - name: Install cloc
-      run: sudo apt-get install -y cloc
-    - name: Firmware source lines count
-      run: cloc --by-file-by-lang flix
-    - name: Overall source lines count
-      run: cloc --by-file-by-lang --exclude-ext=svg,dae,css,hbs,md,json,yaml,yml,toml .
--- a/.markdownlint.json
+++ b/.markdownlint.json
@@ -7,6 +7,8 @@
 	"MD024": false,
 	"MD033": false,
 	"MD034": false,
+	"MD040": false,
+	"MD059": false,
 	"MD044": {
 		"html_elements": false,
 		"code_blocks": false,
@@ -64,5 +66,6 @@
 			"PX4"
 		]
 	},
-	"MD045": false
+	"MD045": false,
+	"MD060": false
 }
--- a/.vscode/c_cpp_properties.json
+++ b/.vscode/c_cpp_properties.json
@@ -6,19 +6,18 @@
 				"${workspaceFolder}/flix",
 				"${workspaceFolder}/gazebo",
 				"${workspaceFolder}/tools/**",
-				"~/.arduino15/packages/esp32/hardware/esp32/3.2.0/cores/esp32",
-				"~/.arduino15/packages/esp32/hardware/esp32/3.2.0/libraries/**",
-				"~/.arduino15/packages/esp32/hardware/esp32/3.2.0/variants/d1_mini32",
-				"~/.arduino15/packages/esp32/tools/esp32-arduino-libs/idf-release_v5.4-2f7dcd86-v1/esp32/**",
-				"~/.arduino15/packages/esp32/tools/esp32-arduino-libs/idf-release_v5.4-2f7dcd86-v1/esp32/dio_qspi/include",
+				"~/.arduino15/packages/esp32/hardware/esp32/3.3.6/cores/esp32",
+				"~/.arduino15/packages/esp32/hardware/esp32/3.3.6/libraries/**",
+				"~/.arduino15/packages/esp32/hardware/esp32/3.3.6/variants/d1_mini32",
+				"~/.arduino15/packages/esp32/tools/esp32-libs/3.3.6/include/**",
 				"~/Arduino/libraries/**",
 				"/usr/include/gazebo-11/",
 				"/usr/include/ignition/math6/"
 			],
 			"forcedInclude": [
 				"${workspaceFolder}/.vscode/intellisense.h",
-				"~/.arduino15/packages/esp32/hardware/esp32/3.2.0/cores/esp32/Arduino.h",
-				"~/.arduino15/packages/esp32/hardware/esp32/3.2.0/variants/d1_mini32/pins_arduino.h",
+				"~/.arduino15/packages/esp32/hardware/esp32/3.3.6/cores/esp32/Arduino.h",
+				"~/.arduino15/packages/esp32/hardware/esp32/3.3.6/variants/d1_mini32/pins_arduino.h",
 				"${workspaceFolder}/flix/cli.ino",
 				"${workspaceFolder}/flix/control.ino",
 				"${workspaceFolder}/flix/estimate.ino",
@@ -31,9 +30,10 @@
 				"${workspaceFolder}/flix/rc.ino",
 				"${workspaceFolder}/flix/time.ino",
 				"${workspaceFolder}/flix/wifi.ino",
-				"${workspaceFolder}/flix/parameters.ino"
+				"${workspaceFolder}/flix/parameters.ino",
+				"${workspaceFolder}/flix/safety.ino"
 			],
-			"compilerPath": "~/.arduino15/packages/esp32/tools/esp-x32/2411/bin/xtensa-esp32-elf-g++",
+			"compilerPath": "~/.arduino15/packages/esp32/tools/esp-x32/2511/bin/xtensa-esp32-elf-g++",
 			"cStandard": "c11",
 			"cppStandard": "c++17",
 			"defines": [
@@ -53,19 +53,18 @@
 			"name": "Mac",
 			"includePath": [
 				"${workspaceFolder}/flix",
-				"~/Library/Arduino15/packages/esp32/hardware/esp32/3.2.0/cores/esp32",
-				"~/Library/Arduino15/packages/esp32/hardware/esp32/3.2.0/libraries/**",
-				"~/Library/Arduino15/packages/esp32/hardware/esp32/3.2.0/variants/d1_mini32",
-				"~/Library/Arduino15/packages/esp32/tools/esp32-arduino-libs/idf-release_v5.4-2f7dcd86-v1/esp32/include/**",
-				"~/Library/Arduino15/packages/esp32/tools/esp32-arduino-libs/idf-release_v5.4-2f7dcd86-v1/esp32/dio_qspi/include",
+				"~/Library/Arduino15/packages/esp32/hardware/esp32/3.3.6/cores/esp32",
+				"~/Library/Arduino15/packages/esp32/hardware/esp32/3.3.6/libraries/**",
+				"~/Library/Arduino15/packages/esp32/hardware/esp32/3.3.6/variants/d1_mini32",
+				"~/Library/Arduino15/packages/esp32/tools/esp32-libs/3.3.6/include/**",
 				"~/Documents/Arduino/libraries/**",
 				"/opt/homebrew/include/gazebo-11/",
 				"/opt/homebrew/include/ignition/math6/"
 			],
 			"forcedInclude": [
 				"${workspaceFolder}/.vscode/intellisense.h",
-				"~/Library/Arduino15/packages/esp32/hardware/esp32/3.2.0/cores/esp32/Arduino.h",
-				"~/Library/Arduino15/packages/esp32/hardware/esp32/3.2.0/variants/d1_mini32/pins_arduino.h",
+				"~/Library/Arduino15/packages/esp32/hardware/esp32/3.3.6/cores/esp32/Arduino.h",
+				"~/Library/Arduino15/packages/esp32/hardware/esp32/3.3.6/variants/d1_mini32/pins_arduino.h",
 				"${workspaceFolder}/flix/flix.ino",
 				"${workspaceFolder}/flix/cli.ino",
 				"${workspaceFolder}/flix/control.ino",
@@ -78,9 +77,10 @@
 				"${workspaceFolder}/flix/rc.ino",
 				"${workspaceFolder}/flix/time.ino",
 				"${workspaceFolder}/flix/wifi.ino",
-				"${workspaceFolder}/flix/parameters.ino"
+				"${workspaceFolder}/flix/parameters.ino",
+				"${workspaceFolder}/flix/safety.ino"
 			],
-			"compilerPath": "~/Library/Arduino15/packages/esp32/tools/esp-x32/2411/bin/xtensa-esp32-elf-g++",
+			"compilerPath": "~/Library/Arduino15/packages/esp32/tools/esp-x32/2511/bin/xtensa-esp32-elf-g++",
 			"cStandard": "c11",
 			"cppStandard": "c++17",
 			"defines": [
@@ -103,17 +103,16 @@
 				"${workspaceFolder}/flix",
 				"${workspaceFolder}/gazebo",
 				"${workspaceFolder}/tools/**",
-				"~/AppData/Local/Arduino15/packages/esp32/hardware/esp32/3.2.0/cores/esp32",
-				"~/AppData/Local/Arduino15/packages/esp32/hardware/esp32/3.2.0/libraries/**",
-				"~/AppData/Local/Arduino15/packages/esp32/hardware/esp32/3.2.0/variants/d1_mini32",
-				"~/AppData/Local/Arduino15/packages/esp32/tools/esp32-arduino-libs/idf-release_v5.4-2f7dcd86-v1/esp32/**",
-				"~/AppData/Local/Arduino15/packages/esp32/tools/esp32-arduino-libs/idf-release_v5.4-2f7dcd86-v1/esp32/dio_qspi/include",
+				"~/AppData/Local/Arduino15/packages/esp32/hardware/esp32/3.3.6/cores/esp32",
+				"~/AppData/Local/Arduino15/packages/esp32/hardware/esp32/3.3.6/libraries/**",
+				"~/AppData/Local/Arduino15/packages/esp32/hardware/esp32/3.3.6/variants/d1_mini32",
+				"~/AppData/Local/Arduino15/packages/esp32/tools/esp32-libs/3.3.6/include/**",
 				"~/Documents/Arduino/libraries/**"
 			],
 			"forcedInclude": [
 				"${workspaceFolder}/.vscode/intellisense.h",
-				"~/AppData/Local/Arduino15/packages/esp32/hardware/esp32/3.2.0/cores/esp32/Arduino.h",
-				"~/AppData/Local/Arduino15/packages/esp32/hardware/esp32/3.2.0/variants/d1_mini32/pins_arduino.h",
+				"~/AppData/Local/Arduino15/packages/esp32/hardware/esp32/3.3.6/cores/esp32/Arduino.h",
+				"~/AppData/Local/Arduino15/packages/esp32/hardware/esp32/3.3.6/variants/d1_mini32/pins_arduino.h",
 				"${workspaceFolder}/flix/cli.ino",
 				"${workspaceFolder}/flix/control.ino",
 				"${workspaceFolder}/flix/estimate.ino",
@@ -126,9 +125,10 @@
 				"${workspaceFolder}/flix/rc.ino",
 				"${workspaceFolder}/flix/time.ino",
 				"${workspaceFolder}/flix/wifi.ino",
-				"${workspaceFolder}/flix/parameters.ino"
+				"${workspaceFolder}/flix/parameters.ino",
+				"${workspaceFolder}/flix/safety.ino"
 			],
-			"compilerPath": "~/AppData/Local/Arduino15/packages/esp32/tools/esp-x32/2411/bin/xtensa-esp32-elf-g++.exe",
+			"compilerPath": "~/AppData/Local/Arduino15/packages/esp32/tools/esp-x32/2511/bin/xtensa-esp32-elf-g++.exe",
 			"cStandard": "c11",
 			"cppStandard": "c++17",
 			"defines": [
--- a/4
+++ b/4
@@ -13,10 +13,10 @@ monitor:

 dependencies .dependencies:
 	arduino-cli core update-index --config-file arduino-cli.yaml
-	arduino-cli core install esp32:esp32@3.2.0 --config-file arduino-cli.yaml
+	arduino-cli core install esp32:esp32@3.3.6 --config-file arduino-cli.yaml
 	arduino-cli lib update-index
 	arduino-cli lib install "FlixPeriph"
-	arduino-cli lib install "MAVLink"@2.0.16
+	arduino-cli lib install "MAVLink"@2.0.25
 	touch .dependencies

 gazebo/build cmake: gazebo/CMakeLists.txt
--- a/README.md
+++ b/README.md
@@ -1,6 +1,9 @@
-# Flix
+<!-- markdownlint-disable MD041 -->

-**Flix** (*flight + X*) — open source ESP32-based quadcopter made from scratch.
+<p align="center">
+  <img src="docs/img/flix.svg" width=180 alt="Flix logo"><br>
+  <b>Flix</b> (<i>flight + X</i>) — open source ESP32-based quadcopter made from scratch.
+</p>

 <table>
  <tr>
@@ -18,15 +21,13 @@
 * Dedicated for education and research.
 * Made from general-purpose components.
 * Simple and clean source code in Arduino (<2k lines firmware).
+* Connectivity using Wi-Fi and MAVLink protocol.
 * Control using USB gamepad, remote control or smartphone.
-* Wi-Fi and MAVLink support.
 * Wireless command line interface and analyzing.
 * Precise simulation with Gazebo.
-* Python library.
+* Python library for scripting and automatic flights.
 * Textbook on flight control theory and practice ([in development](https://quadcopter.dev)).
-* *Position control (using external camera) and autonomous flights¹*.
-
-*¹ — planned.*
+* *Position control (planned)*.

 ## It actually flies

--- a/docs/book/firmware.md
+++ b/docs/book/firmware.md
@@ -35,7 +35,7 @@

 ### Подсистема управления

-Состояние органов управления обрабатывается в функции `interpretControls()` и преобразуется в *команду управления*, которая включает следующее:
+Состояние органов управления обрабатывается в функции `interpretControls()` и преобразуется в **команду управления**, которая включает следующее:

 * `attitudeTarget` *(Quaternion)* — целевая ориентация дрона.
 * `ratesTarget` *(Vector)* — целевые угловые скорости, *рад/с*.
--- a/docs/book/gyro.md
+++ b/docs/book/gyro.md
@@ -87,13 +87,13 @@ Flix поддерживает следующие модели IMU:
 #include <FlixPeriph.h>
 #include <SPI.h>

-MPU9250 IMU(SPI);
+MPU9250 imu(SPI);

 void setup() {
 	Serial.begin(115200);
-	bool success = IMU.begin();
+	bool success = imu.begin();
 	if (!success) {
-		Serial.println("Failed to initialize IMU");
+		Serial.println("Failed to initialize the IMU");
 	}
 }
 ```
@@ -108,21 +108,21 @@ void setup() {
 #include <FlixPeriph.h>
 #include <SPI.h>

-MPU9250 IMU(SPI);
+MPU9250 imu(SPI);

 void setup() {
 	Serial.begin(115200);
-	bool success = IMU.begin();
+	bool success = imu.begin();
 	if (!success) {
-		Serial.println("Failed to initialize IMU");
+		Serial.println("Failed to initialize the IMU");
 	}
 }

 void loop() {
-	IMU.waitForData();
+	imu.waitForData();

 	float gx, gy, gz;
-	IMU.getGyro(gx, gy, gz);
+	imu.getGyro(gx, gy, gz);

 	Serial.printf("gx:%f gy:%f gz:%f\n", gx, gy, gz);
 	delay(50); // замедление вывода
@@ -135,36 +135,36 @@ void loop() {

 ## Конфигурация гироскопа

-В коде Flix настройка IMU происходит в функции `configureIMU`. В этой функции настраиваются три основных параметра гироскопа: диапазон измерений, частота сэмплов и частота LPF-фильтра.
+В коде Flix настройка IMU происходит в функции `configureIMU`. В этой функции настраиваются три основных параметра гироскопа: диапазон измерений, частота сэмплирования и частота LPF-фильтра.

-### Частота сэмплов
+### Частота сэмплирования

-Большинство IMU могут обновлять данные с разной частотой. В полетных контроллерах обычно используется частота обновления от 500 Гц до 8 кГц. Чем выше частота сэмплов, тем выше точность управления полетом, но и больше нагрузка на микроконтроллер.
+Большинство IMU могут обновлять данные с разной частотой. В полетных контроллерах обычно используется частота обновления от 500 Гц до 8 кГц. Чем выше частота, тем выше точность управления полетом, но и тем больше нагрузка на микроконтроллер.

-Частота сэмплов устанавливается методом `setSampleRate()`. В Flix используется частота 1 кГц:
+Частота сэмплирования устанавливается методом `setSampleRate()`. В Flix используется частота 1 кГц:

 ```cpp
 IMU.setRate(IMU.RATE_1KHZ_APPROX);
 ```

-Поскольку не все поддерживаемые IMU могут работать строго на частоте 1 кГц, в библиотеке FlixPeriph существует возможность приближенной настройки частоты сэмплов. Например, у IMU ICM-20948 при такой настройке реальная частота сэмплирования будет равна 1125 Гц.
+Поскольку не все поддерживаемые IMU могут работать строго на частоте 1 кГц, в библиотеке FlixPeriph существует возможность приближенной настройки частоты сэмплирования. Например, у IMU ICM-20948 при такой настройке реальная частота сэмплирования будет равна 1125 Гц.

 Другие доступные для установки в библиотеке FlixPeriph частоты сэмплирования:

-* `RATE_MIN` — минимальная частота сэмплов для конкретного IMU.
+* `RATE_MIN` — минимальная частота для конкретного IMU.
 * `RATE_50HZ_APPROX` — значение, близкое к 50 Гц.
 * `RATE_1KHZ_APPROX` — значение, близкое к 1 кГц.
 * `RATE_8KHZ_APPROX` — значение, близкое к 8 кГц.
-* `RATE_MAX` — максимальная частота сэмплов для конкретного IMU.
+* `RATE_MAX` — максимальная частота для конкретного IMU.

 #### Диапазон измерений

-Большинство MEMS-гироскопов поддерживают несколько диапазонов измерений угловой скорости. Главное преимущество выбора меньшего диапазона — бо́льшая чувствительность. В полетных контроллерах обычно выбирается максимальный диапазон измерений от –2000 до 2000 градусов в секунду, чтобы обеспечить возможность динамичных маневров.
+Большинство MEMS-гироскопов поддерживают несколько диапазонов измерений угловой скорости. Главное преимущество выбора меньшего диапазона — бо́льшая чувствительность. В полетных контроллерах обычно выбирается максимальный диапазон измерений от –2000 до 2000 градусов в секунду, чтобы обеспечить возможность быстрых маневров.

 В библиотеке FlixPeriph диапазон измерений гироскопа устанавливается методом `setGyroRange()`:

 ```cpp
-IMU.setGyroRange(IMU.GYRO_RANGE_2000DPS);
+imu.setGyroRange(imu.GYRO_RANGE_2000DPS);
 ```

 ### LPF-фильтр
@@ -172,7 +172,7 @@ IMU.setGyroRange(IMU.GYRO_RANGE_2000DPS);
 IMU InvenSense могут фильтровать измерения на аппаратном уровне при помощи фильтра нижних частот (LPF). Flix реализует собственный фильтр для гироскопа, чтобы иметь больше гибкости при поддержке разных IMU. Поэтому для встроенного LPF устанавливается максимальная частота среза:

 ```cpp
-IMU.setDLPF(IMU.DLPF_MAX);
+imu.setDLPF(imu.DLPF_MAX);
 ```

 ## Калибровка гироскопа
@@ -181,7 +181,7 @@ IMU.setDLPF(IMU.DLPF_MAX);

 \\[ gyro_{xyz}=rates_{xyz}+bias_{xyz}+noise \\]

-Для качественной работы подсистемы оценки ориентации и управления дроном необходимо оценить *bias* гироскопа и учесть его в вычислениях. Для этого при запуске программы производится калибровка гироскопа, которая реализована в функции `calibrateGyro()`. Эта функция считывает данные с гироскопа в состоянии покоя 1000 раз и усредняет их. Полученные значения считаются *bias* гироскопа и в дальнейшем вычитаются из измерений.
+Для точной работы подсистемы оценки ориентации и управления дроном необходимо оценить *bias* гироскопа и учесть его в вычислениях. Для этого при запуске программы производится калибровка гироскопа, которая реализована в функции `calibrateGyro()`. Эта функция считывает данные с гироскопа в состоянии покоя 1000 раз и усредняет их. Полученные значения считаются *bias* гироскопа и в дальнейшем вычитаются из измерений.

 Программа для вывода данных с гироскопа с калибровкой:

@@ -189,23 +189,23 @@ IMU.setDLPF(IMU.DLPF_MAX);
 #include <FlixPeriph.h>
 #include <SPI.h>

-MPU9250 IMU(SPI);
+MPU9250 imu(SPI);

 float gyroBiasX, gyroBiasY, gyroBiasZ; // bias гироскопа

 void setup() {
 	Serial.begin(115200);
-	bool success = IMU.begin();
+	bool success = imu.begin();
 	if (!success) {
-		Serial.println("Failed to initialize IMU");
+		Serial.println("Failed to initialize the IMU");
 	}
 	calibrateGyro();
 }

 void loop() {
 	float gx, gy, gz;
-	IMU.waitForData();
-	IMU.getGyro(gx, gy, gz);
+	imu.waitForData();
+	imu.getGyro(gx, gy, gz);

 	// Устранение bias гироскопа
 	gx -= gyroBiasX;
@@ -226,9 +226,9 @@ void calibrateGyro() {

 	// Получение 1000 измерений гироскопа
 	for (int i = 0; i < samples; i++) {
-		IMU.waitForData();
+		imu.waitForData();
 		float gx, gy, gz;
-		IMU.getGyro(gx, gy, gz);
+		imu.getGyro(gx, gy, gz);
 		gyroBiasX += gx;
 		gyroBiasY += gy;
 		gyroBiasZ += gz;
--- a/docs/firmware.md
+++ b/docs/firmware.md
@@ -38,13 +38,13 @@ Utility files:

 ### Control subsystem

-Pilot inputs are interpreted in `interpretControls()`, and then converted to the *control command*, which consists of the following:
+Pilot inputs are interpreted in `interpretControls()`, and then converted to the **control command**, which consists of the following:

 * `attitudeTarget` *(Quaternion)* — target attitude of the drone.
 * `ratesTarget` *(Vector)* — target angular rates, *rad/s*.
-* `ratesExtra` *(Vector)* — additional (feed-forward) angular rates , used for yaw rate control in STAB mode, *rad/s*.
+* `ratesExtra` *(Vector)* — additional (feed-forward) angular rates, used for yaw rate control in STAB mode, *rad/s*.
 * `torqueTarget` *(Vector)* — target torque, range [-1, 1].
-* `thrustTarget` *(float)* — collective thrust target, range [0, 1].
+* `thrustTarget` *(float)* — collective motor thrust target, range [0, 1].

 Control command is handled in `controlAttitude()`, `controlRates()`, `controlTorque()` functions. Each function may be skipped if the corresponding control target is set to `NAN`.

@@ -62,6 +62,11 @@ print("Test value: %.2f\n", testValue);

 In order to add a console command, modify the `doCommand()` function in `cli.ino` file.

+> [!IMPORTANT]
+> Avoid using delays in in-flight commands, it will **crash** the drone! (The design is one-threaded.)
+>
+> For on-the-ground commands, use `pause()` function, instead of `delay()`. This function allows to pause in a way that MAVLink connection will continue working.
+
 ## Building the firmware

 See build instructions in [usage.md](usage.md).
--- a/docs/img/flix.svg
+++ b/docs/img/flix.svg
@@ -0,0 +1,38 @@
+<svg xmlns="http://www.w3.org/2000/svg" viewBox="0 0 734.86 378.46">
+  <defs>
+    <style>
+      .a {
+        fill: none;
+        stroke: #d5d5d5;
+        stroke-miterlimit: 10;
+        stroke-width: 31px;
+      }
+
+      .b {
+        fill: #c1c1c1;
+      }
+
+      .c {
+        fill: #ff9400;
+      }
+
+      .d {
+        fill: #d5d5d5;
+      }
+    </style>
+  </defs>
+  <g>
+    <g>
+      <line class="a" x1="448.78" y1="294.23" x2="648.77" y2="93.24"/>
+      <line class="a" x1="449.78" y1="94.24" x2="649.77" y2="295.23"/>
+      <circle class="b" cx="549.27" cy="193.73" r="41.5"/>
+      <circle class="c" cx="449.35" cy="93.74" r="77.95"/>
+      <circle class="c" cx="648.89" cy="93.53" r="77.95"/>
+      <circle class="c" cx="647.89" cy="294.51" r="77.95"/>
+      <circle class="c" cx="448.9" cy="294.51" r="77.95"/>
+    </g>
+    <path class="d" d="M8,161.93q0-17.85,22.36-17.85h4.81V100.57Q35.17,8.49,131.23,8h1q36.87,0,47.31,7.48L181,17.41l1,2.41V50q0,12.32-5.82,12.31-2.43,0-7.4-4.64t-14.19-9a48.63,48.63,0,0,0-21.22-4.41q-12,0-19.17,3.5a18.85,18.85,0,0,0-9.82,10.62,67.35,67.35,0,0,0-3.52,12.06,82.52,82.52,0,0,0-.85,13.39v60.32h27.28q10.86,0,16.05,5.43a17.52,17.52,0,0,1,5.19,12.42,22.5,22.5,0,0,1-1.21,7.36q-1.22,3.51-6.64,7.24t-14.36,3.74H101.64V344.82a56,56,0,0,1-.61,9.65,37.8,37.8,0,0,1-2.56,7.6,11.83,11.83,0,0,1-6.94,6.4q-5,1.93-13.51,1.93H57.08q-10.47,0-15.7-4.71t-5.73-8.44a77.31,77.31,0,0,1-.48-9.53V180.27H29.4Q8,180.27,8,161.93Z"/>
+    <path class="d" d="M201.21,348.2V37q0-23.16,20.86-23.4h22.81q22.8,0,22.8,22.44V346.27a68.92,68.92,0,0,1-.49,9.41,22.59,22.59,0,0,1-2.42,7.12,11.48,11.48,0,0,1-6.67,5.43,47.78,47.78,0,0,1-12.74,2.17H225q-11.4,0-17.58-4.47T201.21,348.2Z"/>
+    <path class="d" d="M284.9,61.08V36.47a40.39,40.39,0,0,1,1.7-12.91,11.36,11.36,0,0,1,6.18-7,25.27,25.27,0,0,1,6.68-2.3c1.45-.15,4-.4,7.76-.72h25.23q10.43,0,16.73,4.7t6.31,18.22V62.05a27.94,27.94,0,0,1-.85,7.11,23,23,0,0,1-2.06,5.43,20,20,0,0,1-2.91,4,10,10,0,0,1-3.52,2.54c-1.21.48-2.54,1-4,1.44a11.53,11.53,0,0,1-3.4.73,13.71,13.71,0,0,0-3.15.48H307.7q-10.43,0-16.61-4.7T284.9,61.08Zm1.94,284.71V166.28q0-22.2,21.83-22.2h20.38q10.92,0,16.62,4t6.67,8.45a60.47,60.47,0,0,1,1,12.18V348.2q0,22.2-21.83,22.2H308.67q-10.43,0-15.64-4.95t-5.7-8.81A90.93,90.93,0,0,1,286.84,345.79Z"/>
+  </g>
+</svg>
--- a/docs/img/imu-axes.png
+++ b/docs/img/imu-axes.png
--- a/docs/img/imu-rot-1.png
+++ b/docs/img/imu-rot-1.png
--- a/docs/img/imu-rot-2.png
+++ b/docs/img/imu-rot-2.png
--- a/docs/img/imu-rot-3.png
+++ b/docs/img/imu-rot-3.png
--- a/docs/img/imu-rot-4.png
+++ b/docs/img/imu-rot-4.png
--- a/docs/img/imu-rot-5.png
+++ b/docs/img/imu-rot-5.png
--- a/docs/img/imu-rot-6.png
+++ b/docs/img/imu-rot-6.png
--- a/docs/img/imu-rot-7.png
+++ b/docs/img/imu-rot-7.png
--- a/docs/img/imu-rot-8.png
+++ b/docs/img/imu-rot-8.png
--- a/docs/img/user/goldarte/1.jpg
+++ b/docs/img/user/goldarte/1.jpg
--- a/docs/img/user/goldarte/2.jpg
+++ b/docs/img/user/goldarte/2.jpg
--- a/docs/img/user/goldarte/video.jpg
+++ b/docs/img/user/goldarte/video.jpg
--- a/docs/img/user/school548/1.jpg
+++ b/docs/img/user/school548/1.jpg
--- a/docs/img/user/school548/2.jpg
+++ b/docs/img/user/school548/2.jpg
--- a/docs/img/user/school548/3.jpg
+++ b/docs/img/user/school548/3.jpg
--- a/docs/img/user/school548/kiraflux-video.jpg
+++ b/docs/img/user/school548/kiraflux-video.jpg
--- a/docs/img/user/school548/kiraflux1.jpg
+++ b/docs/img/user/school548/kiraflux1.jpg
--- a/docs/img/user/school548/kiraflux2.jpg
+++ b/docs/img/user/school548/kiraflux2.jpg
--- a/docs/img/user/school548/tolyan4krut-video.jpg
+++ b/docs/img/user/school548/tolyan4krut-video.jpg
--- a/docs/img/user/school548/tolyan4krut.jpg
+++ b/docs/img/user/school548/tolyan4krut.jpg
--- a/docs/img/user/school548/vlad_tolshinov-video.jpg
+++ b/docs/img/user/school548/vlad_tolshinov-video.jpg
--- a/docs/img/user/school548/vlad_tolshinov1.jpg
+++ b/docs/img/user/school548/vlad_tolshinov1.jpg
--- a/docs/img/user/school548/vlad_tolshinov2.jpg
+++ b/docs/img/user/school548/vlad_tolshinov2.jpg
--- a/docs/troubleshooting.md
+++ b/docs/troubleshooting.md
@@ -4,7 +4,7 @@

 Do the following:

-* **Check ESP32 core is installed**. Check if the version matches the one used in the [tutorial](usage.md#firmware).
+* **Check ESP32 core is installed**. Check if the version matches the one used in the [tutorial](usage.md#building-the-firmware).
 * **Check libraries**. Install all the required libraries from the tutorial. Make sure there are no MPU9250 or other peripherals libraries that may conflict with the ones used in the tutorial.
 * **Check the chosen board**. The correct board to choose in Arduino IDE for ESP32 Mini is *WEMOS D1 MINI ESP32*.

@@ -25,7 +25,7 @@ Do the following:
  * The `accel` and `gyro` fields should change as you move the drone.
 * **Calibrate the accelerometer.** if is wasn't done before. Type `ca` command in Serial Monitor and follow the instructions.
 * **Check the attitude estimation**. Connect to the drone using QGroundControl. Rotate the drone in different orientations and check if the attitude estimation shown in QGroundControl is correct.
-* **Check the IMU orientation is set correctly**. If the attitude estimation is rotated, make sure `rotateIMU` function is defined correctly in `imu.ino` file.
+* **Check the IMU orientation is set correctly**. If the attitude estimation is rotated, set the correct IMU orientation as described in the [tutorial](usage.md#define-imu-orientation).
 * **Check the motors type**. Motors with exact 3.7V voltage are needed, not ranged working voltage (3.7V — 6V).
 * **Check the motors**. Perform the following commands using Serial Monitor:
  * `mfr` — should rotate front right motor (counter-clockwise).
--- a/docs/usage.md
+++ b/docs/usage.md
@@ -12,7 +12,7 @@ Beginners can [download the source code as a ZIP archive](https://github.com/oka

 ## Building the firmware

-You can build and upload the firmware using either **Arduino IDE** (easier for beginners) or a **command line**.
+You can build and upload the firmware using either **Arduino IDE** (easier for beginners) or **command line**.

 ### Arduino IDE (Windows, Linux, macOS)

@@ -20,10 +20,10 @@ You can build and upload the firmware using either **Arduino IDE** (easier for b

 1. Install [Arduino IDE](https://www.arduino.cc/en/software) (version 2 is recommended).
 2. *Windows users might need to install [USB to UART bridge driver from Silicon Labs](https://www.silabs.com/developers/usb-to-uart-bridge-vcp-drivers).*
-3. Install ESP32 core, version 3.2.0. See the [official Espressif's instructions](https://docs.espressif.com/projects/arduino-esp32/en/latest/installing.html#installing-using-arduino-ide) on installing ESP32 Core in Arduino IDE.
+3. Install ESP32 core, version 3.3.6. See the [official Espressif's instructions](https://docs.espressif.com/projects/arduino-esp32/en/latest/installing.html#installing-using-arduino-ide) on installing ESP32 Core in Arduino IDE.
 4. Install the following libraries using [Library Manager](https://docs.arduino.cc/software/ide-v2/tutorials/ide-v2-installing-a-library):
   * `FlixPeriph`, the latest version.
-   * `MAVLink`, version 2.0.16.
+   * `MAVLink`, version 2.0.25.
 5. Open the `flix/flix.ino` sketch from downloaded firmware sources in Arduino IDE.
 6. Connect your ESP32 board to the computer and choose correct board type in Arduino IDE (*WEMOS D1 MINI ESP32* for ESP32 Mini) and the port.
 7. [Build and upload](https://docs.arduino.cc/software/ide-v2/tutorials/getting-started/ide-v2-uploading-a-sketch) the firmware using Arduino IDE.
@@ -73,14 +73,6 @@ ICM20948 imu(SPI);  // For ICM-20948
 MPU6050 imu(Wire);  // For MPU-6050
 ```

-### Setup the IMU orientation
-
-The IMU orientation is defined in `rotateIMU` function in the `imu.ino` file. Change it so it converts the IMU axes to the drone's axes correctly. **Drone axes are X forward, Y left, Z up**:
-
-<img src="img/drone-axes.svg" width="200">
-
-See various [IMU boards axes orientations table](https://github.com/okalachev/flixperiph/?tab=readme-ov-file#imu-axes-orientation) to help you set up the correct orientation.
-
 ### Connect using QGroundControl

 QGroundControl is a ground control station software that can be used to monitor and control the drone.
@@ -88,7 +80,7 @@ QGroundControl is a ground control station software that can be used to monitor
 1. Install mobile or desktop version of [QGroundControl](https://docs.qgroundcontrol.com/master/en/qgc-user-guide/getting_started/download_and_install.html).
 2. Power up the drone.
 3. Connect your computer or smartphone to the appeared `flix` Wi-Fi network (password: `flixwifi`).
-4. Launch QGroundControl app. It should connect and begin showing the drone's telemetry automatically
+4. Launch QGroundControl app. It should connect and begin showing the drone's telemetry automatically.

 ### Access console

@@ -104,11 +96,37 @@ To access the console using QGroundControl:

 1. Connect to the drone using QGroundControl app.
 2. Go to the QGroundControl menu ⇒ *Vehicle Setup* ⇒ *Analyze Tools* ⇒ *MAVLink Console*.
-   <img src="img/cli.png" width="400">
+
+<img src="img/cli.png" width="400">

 > [!TIP]
 > Use `help` command to see the list of available commands.

+### Access parameters
+
+The drone is configured using parameters. To access and modify them, go to the QGroundControl menu ⇒ *Vehicle Setup* ⇒ *Parameters*:
+
+<img src="img/parameters.png" width="400">
+
+You can also work with parameters using `p` command in the console. Parameter names are case-insensitive.
+
+### Define IMU orientation
+
+Use parameters, to define the IMU board axes orientation relative to the drone's axes: `IMU_ROT_ROLL`, `IMU_ROT_PITCH`, and `IMU_ROT_YAW`.
+
+The drone has *X* axis pointing forward, *Y* axis pointing left, and *Z* axis pointing up, and the supported IMU boards have *X* axis pointing to the pins side and *Z* axis pointing up from the component side:
+
+<img src="img/imu-axes.png" width="200">
+
+Use the following table to set the parameters for common IMU orientations:
+
+|Orientation|Parameters|Orientation|Parameters|
+|:-:|-|-|-|
+|<img src="img/imu-rot-1.png" width="180">|`IMU_ROT_ROLL` = 0<br>`IMU_ROT_PITCH` = 0<br>`IMU_ROT_YAW` = 0    |<img src="img/imu-rot-5.png" width="180">|`IMU_ROT_ROLL` = 3.142<br>`IMU_ROT_PITCH` = 0<br>`IMU_ROT_YAW` = 0|
+|<img src="img/imu-rot-2.png" width="180">|`IMU_ROT_ROLL` = 0<br>`IMU_ROT_PITCH` = 0<br>`IMU_ROT_YAW` = 1.571|<img src="img/imu-rot-6.png" width="180">|`IMU_ROT_ROLL` = 3.142<br>`IMU_ROT_PITCH` = 0<br>`IMU_ROT_YAW` = -1.571|
+|<img src="img/imu-rot-3.png" width="180">|`IMU_ROT_ROLL` = 0<br>`IMU_ROT_PITCH` = 0<br>`IMU_ROT_YAW` = 3.142|<img src="img/imu-rot-7.png" width="180">|`IMU_ROT_ROLL` = 3.142<br>`IMU_ROT_PITCH` = 0<br>`IMU_ROT_YAW` = 3.142|
+|<img src="img/imu-rot-4.png" width="180"><br>☑️ **Default**|<br>`IMU_ROT_ROLL` = 0<br>`IMU_ROT_PITCH` = 0<br>`IMU_ROT_YAW` = -1.571|<img src="img/imu-rot-8.png" width="180">|`IMU_ROT_ROLL` = 3.142<br>`IMU_ROT_PITCH` = 0<br>`IMU_ROT_YAW` = 1.571|
+
 ### Calibrate accelerometer

 Before flight you need to calibrate the accelerometer:
@@ -125,9 +143,9 @@ Before flight you need to calibrate the accelerometer:
   * The `accel` and `gyro` fields should change as you move the drone.
   * The `landed` field should be `1` when the drone is still on the ground and `0` when you lift it up.

-2. Check the attitude estimation: connect to the drone using QGroundControl, rotate the drone in different orientations and check if the attitude estimation shown in QGroundControl is correct. Attitude indicator in QGroundControl is shown below:
+2. Check the attitude estimation: connect to the drone using QGroundControl, rotate the drone in different orientations and check if the attitude estimation shown in QGroundControl is correct. Compare your attitude indicator (in the *large vertical* mode) to the video:

-   <img src="img/qgc-attitude.png" height="200">
+    <a href="https://youtu.be/yVRN23-GISU"><img width=300 src="https://i3.ytimg.com/vi/yVRN23-GISU/maxresdefault.jpg"></a>

 3. Perform motor tests in the console. Use the following commands **— remove the propellers before running the tests!**

@@ -136,6 +154,10 @@ Before flight you need to calibrate the accelerometer:
   * `mrl` — should rotate rear left motor (counter-clockwise).
   * `mrr` — should rotate rear right motor (clockwise).

+   Rotation diagram:
+
+   <img src="img/motors.svg" width=200>
+
 > [!WARNING]
 > Never run the motors when powering the drone from USB, always use the battery for that.

@@ -143,7 +165,7 @@ Before flight you need to calibrate the accelerometer:

 There are several ways to control the drone's flight: using **smartphone** (Wi-Fi), using **SBUS remote control**, or using **USB remote control** (Wi-Fi).

-### Control with smartphone
+### Control with a smartphone

 1. Install [QGroundControl mobile app](https://docs.qgroundcontrol.com/master/en/qgc-user-guide/getting_started/download_and_install.html#android) on your smartphone.
 2. Power the drone using the battery.
@@ -153,9 +175,9 @@ There are several ways to control the drone's flight: using **smartphone** (Wi-F
 6. Use the virtual joystick to fly the drone!

 > [!TIP]
-> Decrease `CNT_TILT_MAX` parameter when flying using the smartphone to make the controls less sensitive.
+> Decrease `CTL_TILT_MAX` parameter when flying using the smartphone to make the controls less sensitive.

-### Control with remote control
+### Control with a remote control

 Before using remote SBUS-connected remote control, you need to calibrate it:

@@ -163,7 +185,7 @@ Before using remote SBUS-connected remote control, you need to calibrate it:
 2. Type `cr` command and follow the instructions.
 3. Use the remote control to fly the drone!

-### Control with USB remote control
+### Control with a USB remote control

 If your drone doesn't have RC receiver installed, you can use USB remote control and QGroundControl app to fly it.

@@ -211,9 +233,9 @@ The default mode is *STAB*. In this mode, the drone stabilizes its attitude (ori

 In this mode, the pilot controls the angular rates. This control method is difficult to fly and mostly used in FPV racing.

-#### MANUAL
+#### RAW

-Manual mode disables all the stabilization, and the pilot inputs are passed directly to the motors. This mode is intended for testing and demonstration purposes only, and basically the drone **cannot fly in this mode**.
+*RAW* mode disables all the stabilization, and the pilot inputs are mixed directly to the motors. The IMU sensor is not involved. This mode is intended for testing and demonstration purposes only, and basically the drone **cannot fly in this mode**.

 #### AUTO

@@ -221,15 +243,43 @@ In this mode, the pilot inputs are ignored (except the mode switch, if configure

 If the pilot moves the control sticks, the drone will switch back to *STAB* mode.

-## Adjusting parameters
+## Wi-Fi configuration

-You can adjust some of the drone's parameters (include PID coefficients) in QGroundControl. In order to do that, go to the QGroundControl menu ⇒ *Vehicle Setup* ⇒ *Parameters*.
+You can configure the Wi-Fi using parameters and console commands.

-<img src="img/parameters.png" width="400">
+The Wi-Fi mode is chosen using `WIFI_MODE` parameter in QGroundControl or in the console:
+
+* `0` — Wi-Fi is disabled.
+* `1` — Access Point mode (*AP*) — the drone creates a Wi-Fi network.
+* `2` — Client mode (*STA*) — the drone connects to an existing Wi-Fi network.
+* `3` — *ESP-NOW (not implemented yet)*.
+
+> [!WARNING]
+> Tests showed that Client mode may cause **additional delays** in remote control (due to retranslations), so it's generally not recommended.
+
+The SSID and password are configured using the `ap` and `sta` console commands:
+
+```
+ap <ssid> <password>
+sta <ssid> <password>
+```
+
+Example of configuring the Access Point mode:
+
+```
+ap my-flix-ssid mypassword123
+p WIFI_MODE 1
+```
+
+Disabling Wi-Fi:
+
+```
+p WIFI_MODE 0
+```

 ## Flight log

-After the flight, you can download the flight log for analysis wirelessly. Use the following for that:
+After the flight, you can download the flight log for analysis wirelessly. Use the following command on your computer for that:

 ```bash
 make log
--- a/docs/user.md
+++ b/docs/user.md
@@ -4,12 +4,67 @@ This page contains user-built drones based on the Flix project. Publish your pro

 ---

+Author: [goldarte](https://t.me/goldarte).<br>
+
+<img src="img/user/goldarte/1.jpg" height=150> <img src="img/user/goldarte/2.jpg" height=150>
+
+**Flight video:**
+
+<a href="https://drive.google.com/file/d/1nQtFjEcGGLx-l4xkL5ko9ZpOTVU-WDjL/view?usp=sharing"><img height=200 src="img/user/goldarte/video.jpg"></a>
+
+---
+
+## School 548 course
+
+Special course on quadcopter design and engineering took place in october-november 2025 in School 548, Moscow. The course included UAV control theory, electronics, drone assembly and setup practice, using the Flix project.
+
+<img height=200 src="img/user/school548/1.jpg"> <img height=200 src="img/user/school548/2.jpg"> <img height=200 src="img/user/school548/3.jpg">
+
+STL files and other materials: see [here](https://drive.google.com/drive/folders/1wTUzj087LjKQQl3Lz5CjHCuobxoykhyp?usp=share_link).
+
+### Selected works
+
+Author: [KiraFlux](https://t.me/@kiraflux_0XC0000005).<br>
+Description: **custom ESPNOW remote control** was implemented, modified firmware to support ESPNOW protocol.<br>
+Telegram posts: [1](https://t.me/opensourcequadcopter/106), [2](https://t.me/opensourcequadcopter/114).<br>
+Modified Flix firmware: https://github.com/KiraFlux/flix/tree/klyax.<br>
+Remote control project: https://github.com/KiraFlux/ESP32-DJC.<br>
+Drone design: https://github.com/KiraFlux/Klyax.<br>
+
+<img src="img/user/school548/kiraflux1.jpg" height=150> <img src="img/user/school548/kiraflux2.jpg" height=150>
+
+**ESPNOW remote control demonstration**:
+
+<img height=200 src="img/user/school548/kiraflux-video.jpg"><a href="https://drive.google.com/file/d/1soHDAeHQWnm97Y4dg4nWevJuMiTdJJXW/view?usp=sharing"></a>
+
+Author: [tolyan4krut](https://t.me/tolyan4krut).<br>
+Description: the first drone based on ESP32-S3-CAM board **with a camera**, implementing Wi-Fi video streaming. Runs HTTP server and HTTP video stream.<br>
+Modified Flix firmware: https://github.com/CatRey/Flix-Camera-Streaming.<br>
+[Telegram post](https://t.me/opensourcequadcopter/117).
+
+<img src="img/user/school548/tolyan4krut.jpg" height=150>
+
+**Video streaming and flight demonstration**:
+
+<a href="https://drive.google.com/file/d/1KuOBsujLsk7q8FoqKD8u7uoq4ptS5onp/view?usp=sharing"><img height=200 src="img/user/school548/tolyan4krut-video.jpg"></a>
+
+Author: [Vlad Tolshinov](https://t.me/Vlad_Tolshinov).<br>
+Description: custom frame with enlarged arm length, which provides very high flight stability, 65 mm props.
+
+<img src="img/user/school548/vlad_tolshinov1.jpg" height=150> <img src="img/user/school548/vlad_tolshinov2.jpg" height=150>
+
+**Flight video**:
+
+<a href="https://drive.google.com/file/d/1zu00DZxhC7DJ9Z2mYjtxdNQqOOLAyYbp/view?usp=sharing"><img height=200 src="img/user/school548/vlad_tolshinov-video.jpg"></a>
+
+---
+
 ## RoboCamp

 Author: RoboCamp participants.<br>
 Description: 3D-printed and wooden frames, ESP32 Mini, DC-DC buck-boost converters. BetaFPV LiteRadio 3 to control the drones via Wi-Fi connection.<br>
 Features: altitude hold, obstacle avoidance, autonomous flight elements.<br>
-Some of the designed model files: https://drive.google.com/drive/folders/18YHWGquKeIevzrMH4-OUT-zKXMETTEUu?usp=share_link.
+Some of the designed model files: see [here](https://drive.google.com/drive/folders/18YHWGquKeIevzrMH4-OUT-zKXMETTEUu?usp=share_link).

 RoboCamp took place in July 2025, Saint Petersburg, where 9 participants designed and built their own drones using the Flix project, and then modified the firmware to complete specific flight tasks.

--- a/flix/cli.ino
+++ b/flix/cli.ino
@@ -8,10 +8,10 @@
 #include "util.h"

 extern const int MOTOR_REAR_LEFT, MOTOR_REAR_RIGHT, MOTOR_FRONT_RIGHT, MOTOR_FRONT_LEFT;
-extern const int ACRO, STAB, AUTO;
+extern const int RAW, ACRO, STAB, AUTO;
 extern float t, dt, loopRate;
 extern uint16_t channels[16];
-extern float controlRoll, controlPitch, controlThrottle, controlYaw, controlMode;
+extern float controlTime;
 extern int mode;
 extern bool armed;

@@ -35,8 +35,11 @@ const char* motd =
 "imu - show IMU data\n"
 "arm - arm the drone\n"
 "disarm - disarm the drone\n"
-"stab/acro/auto - set mode\n"
+"raw/stab/acro/auto - set mode\n"
 "rc - show RC data\n"
+"wifi - show Wi-Fi info\n"
+"ap <ssid> <password> - setup Wi-Fi access point\n"
+"sta <ssid> <password> - setup Wi-Fi client mode\n"
 "mot - show motor output\n"
 "log [dump] - print log header [and data]\n"
 "cr - calibrate RC\n"
@@ -53,9 +56,7 @@ void print(const char* format, ...) {
 	vsnprintf(buf, sizeof(buf), format, args);
 	va_end(args);
 	Serial.print(buf);
-#if WIFI_ENABLED
 	mavlinkPrint(buf);
-#endif
 }

 void pause(float duration) {
@@ -63,9 +64,7 @@ void pause(float duration) {
 	while (t - start < duration) {
 		step();
 		handleInput();
-#if WIFI_ENABLED
 		processMavlink();
-#endif
 		delay(50);
 	}
 }
@@ -116,6 +115,8 @@ void doCommand(String str, bool echo = false) {
 		armed = true;
 	} else if (command == "disarm") {
 		armed = false;
+	} else if (command == "raw") {
+		mode = RAW;
 	} else if (command == "stab") {
 		mode = STAB;
 	} else if (command == "acro") {
@@ -129,8 +130,15 @@ void doCommand(String str, bool echo = false) {
 		}
 		print("\nroll: %g pitch: %g yaw: %g throttle: %g mode: %g\n",
 			controlRoll, controlPitch, controlYaw, controlThrottle, controlMode);
+		print("time: %.1f\n", controlTime);
 		print("mode: %s\n", getModeName());
 		print("armed: %d\n", armed);
+	} else if (command == "wifi") {
+		printWiFiInfo();
+	} else if (command == "ap") {
+		configWiFi(true, arg0.c_str(), arg1.c_str());
+	} else if (command == "sta") {
+		configWiFi(false, arg0.c_str(), arg1.c_str());
 	} else if (command == "mot") {
 		print("front-right %g front-left %g rear-right %g rear-left %g\n",
 			motors[MOTOR_FRONT_RIGHT], motors[MOTOR_FRONT_LEFT], motors[MOTOR_REAR_RIGHT], motors[MOTOR_REAR_LEFT]);
--- a/flix/control.ino
+++ b/flix/control.ino
@@ -34,10 +34,16 @@
 #define TILT_MAX radians(30)
 #define RATES_D_LPF_ALPHA 0.2 // cutoff frequency ~ 40 Hz

-const int MANUAL = 0, ACRO = 1, STAB = 2, AUTO = 3; // flight modes
+const int RAW = 0, ACRO = 1, STAB = 2, AUTO = 3; // flight modes
 int mode = STAB;
 bool armed = false;

+Quaternion attitudeTarget;
+Vector ratesTarget;
+Vector ratesExtra; // feedforward rates
+Vector torqueTarget;
+float thrustTarget;
+
 PID rollRatePID(ROLLRATE_P, ROLLRATE_I, ROLLRATE_D, ROLLRATE_I_LIM, RATES_D_LPF_ALPHA);
 PID pitchRatePID(PITCHRATE_P, PITCHRATE_I, PITCHRATE_D, PITCHRATE_I_LIM, RATES_D_LPF_ALPHA);
 PID yawRatePID(YAWRATE_P, YAWRATE_I, YAWRATE_D);
@@ -47,12 +53,6 @@ PID yawPID(YAW_P, 0, 0);
 Vector maxRate(ROLLRATE_MAX, PITCHRATE_MAX, YAWRATE_MAX);
 float tiltMax = TILT_MAX;

-Quaternion attitudeTarget;
-Vector ratesTarget;
-Vector ratesExtra; // feedforward rates
-Vector torqueTarget;
-float thrustTarget;
-
 extern const int MOTOR_REAR_LEFT, MOTOR_REAR_RIGHT, MOTOR_FRONT_RIGHT, MOTOR_FRONT_LEFT;
 extern float controlRoll, controlPitch, controlThrottle, controlYaw, controlMode;

@@ -65,7 +65,6 @@ void control() {
 }

 void interpretControls() {
-	// NOTE: put ACRO or MANUAL modes there if you want to use them
 	if (controlMode < 0.25) mode = STAB;
 	if (controlMode < 0.75) mode = STAB;
 	if (controlMode > 0.75) mode = STAB;
@@ -75,6 +74,8 @@ void interpretControls() {
 	if (controlThrottle < 0.05 && controlYaw > 0.95) armed = true; // arm gesture
 	if (controlThrottle < 0.05 && controlYaw < -0.95) armed = false; // disarm gesture

+	if (abs(controlYaw) < 0.1) controlYaw = 0; // yaw dead zone
+
 	thrustTarget = controlThrottle;

 	if (mode == STAB) {
@@ -91,10 +92,10 @@ void interpretControls() {
 		ratesTarget.z = -controlYaw * maxRate.z; // positive yaw stick means clockwise rotation in FLU
 	}

-	if (mode == MANUAL) { // passthrough mode
+	if (mode == RAW) { // direct torque control
 		attitudeTarget.invalidate(); // skip attitude control
 		ratesTarget.invalidate(); // skip rate control
-		torqueTarget = Vector(controlRoll, controlPitch, -controlYaw) * 0.01;
+		torqueTarget = Vector(controlRoll, controlPitch, -controlYaw) * 0.1;
 	}
 }

@@ -155,7 +156,7 @@ void controlTorque() {

 const char* getModeName() {
 	switch (mode) {
-		case MANUAL: return "MANUAL";
+		case RAW: return "RAW";
 		case ACRO: return "ACRO";
 		case STAB: return "STAB";
 		case AUTO: return "AUTO";
--- a/flix/estimate.ino
+++ b/flix/estimate.ino
@@ -8,8 +8,12 @@
 #include "lpf.h"
 #include "util.h"

-#define WEIGHT_ACC 0.003
-#define RATES_LFP_ALPHA 0.2 // cutoff frequency ~ 40 Hz
+Vector rates; // estimated angular rates, rad/s
+Quaternion attitude; // estimated attitude
+bool landed;
+
+float accWeight = 0.003;
+LowPassFilter<Vector> ratesFilter(0.2); // cutoff frequency ~ 40 Hz

 void estimate() {
 	applyGyro();
@@ -18,7 +22,6 @@ void estimate() {

 void applyGyro() {
 	// filter gyro to get angular rates
-	static LowPassFilter<Vector> ratesFilter(RATES_LFP_ALPHA);
 	rates = ratesFilter.update(gyro);

 	// apply rates to attitude
@@ -34,7 +37,7 @@ void applyAcc() {

 	// calculate accelerometer correction
 	Vector up = Quaternion::rotateVector(Vector(0, 0, 1), attitude);
-	Vector correction = Vector::rotationVectorBetween(acc, up) * WEIGHT_ACC;
+	Vector correction = Vector::rotationVectorBetween(acc, up) * accWeight;

 	// apply correction
 	attitude = Quaternion::rotate(attitude, Quaternion::fromRotationVector(correction));
--- a/flix/flix.ino
+++ b/flix/flix.ino
@@ -7,18 +7,14 @@
 #include "quaternion.h"
 #include "util.h"

-#define WIFI_ENABLED 1

-float t = NAN; // current step time, s
-float dt; // time delta from previous step, s
-float controlRoll, controlPitch, controlYaw, controlThrottle; // pilot's inputs, range [-1, 1]
-float controlMode = NAN;
-Vector gyro; // gyroscope data
-Vector acc; // accelerometer data, m/s/s
-Vector rates; // filtered angular rates, rad/s
-Quaternion attitude; // estimated attitude
-bool landed; // are we landed and stationary
-float motors[4]; // normalized motors thrust in range [0..1]
+extern float t, dt;
+extern float controlRoll, controlPitch, controlYaw, controlThrottle, controlMode;
+extern Vector gyro, acc;
+extern Vector rates;
+extern Quaternion attitude;
+extern bool landed;
+extern float motors[4];

 void setup() {
 	Serial.begin(115200);
@@ -28,9 +24,7 @@ void setup() {
 	setupLED();
 	setupMotors();
 	setLED(true);
-#if WIFI_ENABLED
 	setupWiFi();
-#endif
 	setupIMU();
 	setupRC();
 	setLED(false);
@@ -45,9 +39,7 @@ void loop() {
 	control();
 	sendMotors();
 	handleInput();
-#if WIFI_ENABLED
 	processMavlink();
-#endif
 	logData();
 	syncParameters();
 }
--- a/flix/imu.ino
+++ b/flix/imu.ino
@@ -10,10 +10,14 @@
 #include "util.h"

 MPU9250 imu(SPI);
+Vector imuRotation(0, 0, -PI / 2); // imu orientation as Euler angles

+Vector gyro; // gyroscope output, rad/s
+Vector gyroBias;
+
+Vector acc; // accelerometer output, m/s/s
 Vector accBias;
 Vector accScale(1, 1, 1);
-Vector gyroBias;

 void setupIMU() {
 	print("Setup IMU\n");
@@ -37,24 +41,18 @@ void readIMU() {
 	// apply scale and bias
 	acc = (acc - accBias) / accScale;
 	gyro = gyro - gyroBias;
-	// rotate
-	rotateIMU(acc);
-	rotateIMU(gyro);
-}
-
-void rotateIMU(Vector& data) {
-	// Rotate from LFD to FLU
-	// NOTE: In case of using other IMU orientation, change this line:
-	data = Vector(data.y, data.x, -data.z);
-	// Axes orientation for various boards: https://github.com/okalachev/flixperiph#imu-axes-orientation
+	// rotate to body frame
+	Quaternion rotation = Quaternion::fromEuler(imuRotation);
+	acc = Quaternion::rotateVector(acc, rotation.inversed());
+	gyro = Quaternion::rotateVector(gyro, rotation.inversed());
 }

 void calibrateGyroOnce() {
 	static Delay landedDelay(2);
 	if (!landedDelay.update(landed)) return; // calibrate only if definitely stationary

-	static LowPassFilter<Vector> gyroCalibrationFilter(0.001);
-	gyroBias = gyroCalibrationFilter.update(gyro);
+	static LowPassFilter<Vector> gyroBiasFilter(0.001);
+	gyroBias = gyroBiasFilter.update(gyro);
 }

 void calibrateAccel() {
--- a/flix/mavlink.ino
+++ b/flix/mavlink.ino
@@ -3,21 +3,16 @@

 // MAVLink communication

-#if WIFI_ENABLED
-
 #include <MAVLink.h>
 #include "util.h"

-#define SYSTEM_ID 1
-#define MAVLINK_RATE_SLOW 1
-#define MAVLINK_RATE_FAST 10
-#define MAVLINK_CONTROL_YAW_DEAD_ZONE 0.1f
+extern float controlTime;

 bool mavlinkConnected = false;
 String mavlinkPrintBuffer;
-
-extern float controlTime;
-extern float controlRoll, controlPitch, controlThrottle, controlYaw, controlMode;
+int mavlinkSysId = 1;
+Rate telemetryFast(10);
+Rate telemetrySlow(2);

 void processMavlink() {
 	sendMavlink();
@@ -30,10 +25,8 @@ void sendMavlink() {
 	mavlink_message_t msg;
 	uint32_t time = t * 1000;

-	static Rate slow(MAVLINK_RATE_SLOW), fast(MAVLINK_RATE_FAST);
-
-	if (slow) {
-		mavlink_msg_heartbeat_pack(SYSTEM_ID, MAV_COMP_ID_AUTOPILOT1, &msg, MAV_TYPE_QUADROTOR, MAV_AUTOPILOT_GENERIC,
+	if (telemetrySlow) {
+		mavlink_msg_heartbeat_pack(mavlinkSysId, MAV_COMP_ID_AUTOPILOT1, &msg, MAV_TYPE_QUADROTOR, MAV_AUTOPILOT_GENERIC,
 			(armed ? MAV_MODE_FLAG_SAFETY_ARMED : 0) |
 			((mode == STAB) ? MAV_MODE_FLAG_STABILIZE_ENABLED : 0) |
 			((mode == AUTO) ? MAV_MODE_FLAG_AUTO_ENABLED : MAV_MODE_FLAG_MANUAL_INPUT_ENABLED),
@@ -42,27 +35,27 @@ void sendMavlink() {

 		if (!mavlinkConnected) return; // send only heartbeat until connected

-		mavlink_msg_extended_sys_state_pack(SYSTEM_ID, MAV_COMP_ID_AUTOPILOT1, &msg,
+		mavlink_msg_extended_sys_state_pack(mavlinkSysId, MAV_COMP_ID_AUTOPILOT1, &msg,
 			MAV_VTOL_STATE_UNDEFINED, landed ? MAV_LANDED_STATE_ON_GROUND : MAV_LANDED_STATE_IN_AIR);
 		sendMessage(&msg);
 	}

-	if (fast && mavlinkConnected) {
+	if (telemetryFast && mavlinkConnected) {
 		const float zeroQuat[] = {0, 0, 0, 0};
-		mavlink_msg_attitude_quaternion_pack(SYSTEM_ID, MAV_COMP_ID_AUTOPILOT1, &msg,
+		mavlink_msg_attitude_quaternion_pack(mavlinkSysId, MAV_COMP_ID_AUTOPILOT1, &msg,
 			time, attitude.w, attitude.x, -attitude.y, -attitude.z, rates.x, -rates.y, -rates.z, zeroQuat); // convert to frd
 		sendMessage(&msg);

-		mavlink_msg_rc_channels_raw_pack(SYSTEM_ID, MAV_COMP_ID_AUTOPILOT1, &msg, controlTime * 1000, 0,
+		mavlink_msg_rc_channels_raw_pack(mavlinkSysId, MAV_COMP_ID_AUTOPILOT1, &msg, controlTime * 1000, 0,
 			channels[0], channels[1], channels[2], channels[3], channels[4], channels[5], channels[6], channels[7], UINT8_MAX);
 		if (channels[0] != 0) sendMessage(&msg); // 0 means no RC input

 		float controls[8];
 		memcpy(controls, motors, sizeof(motors));
-		mavlink_msg_actuator_control_target_pack(SYSTEM_ID, MAV_COMP_ID_AUTOPILOT1, &msg, time, 0, controls);
+		mavlink_msg_actuator_control_target_pack(mavlinkSysId, MAV_COMP_ID_AUTOPILOT1, &msg, time, 0, controls);
 		sendMessage(&msg);

-		mavlink_msg_scaled_imu_pack(SYSTEM_ID, MAV_COMP_ID_AUTOPILOT1, &msg, time,
+		mavlink_msg_scaled_imu_pack(mavlinkSysId, MAV_COMP_ID_AUTOPILOT1, &msg, time,
 			acc.x * 1000, -acc.y * 1000, -acc.z * 1000, // convert to frd
 			gyro.x * 1000, -gyro.y * 1000, -gyro.z * 1000,
 			0, 0, 0, 0);
@@ -97,7 +90,7 @@ void handleMavlink(const void *_msg) {
 	if (msg.msgid == MAVLINK_MSG_ID_MANUAL_CONTROL) {
 		mavlink_manual_control_t m;
 		mavlink_msg_manual_control_decode(&msg, &m);
-		if (m.target && m.target != SYSTEM_ID) return; // 0 is broadcast
+		if (m.target && m.target != mavlinkSysId) return; // 0 is broadcast

 		controlThrottle = m.z / 1000.0f;
 		controlPitch = m.x / 1000.0f;
@@ -105,18 +98,16 @@ void handleMavlink(const void *_msg) {
 		controlYaw = m.r / 1000.0f;
 		controlMode = NAN;
 		controlTime = t;
-
-		if (abs(controlYaw) < MAVLINK_CONTROL_YAW_DEAD_ZONE) controlYaw = 0;
 	}

 	if (msg.msgid == MAVLINK_MSG_ID_PARAM_REQUEST_LIST) {
 		mavlink_param_request_list_t m;
 		mavlink_msg_param_request_list_decode(&msg, &m);
-		if (m.target_system && m.target_system != SYSTEM_ID) return;
+		if (m.target_system && m.target_system != mavlinkSysId) return;

 		mavlink_message_t msg;
 		for (int i = 0; i < parametersCount(); i++) {
-			mavlink_msg_param_value_pack(SYSTEM_ID, MAV_COMP_ID_AUTOPILOT1, &msg,
+			mavlink_msg_param_value_pack(mavlinkSysId, MAV_COMP_ID_AUTOPILOT1, &msg,
 				getParameterName(i), getParameter(i), MAV_PARAM_TYPE_REAL32, parametersCount(), i);
 			sendMessage(&msg);
 		}
@@ -125,7 +116,7 @@ void handleMavlink(const void *_msg) {
 	if (msg.msgid == MAVLINK_MSG_ID_PARAM_REQUEST_READ) {
 		mavlink_param_request_read_t m;
 		mavlink_msg_param_request_read_decode(&msg, &m);
-		if (m.target_system && m.target_system != SYSTEM_ID) return;
+		if (m.target_system && m.target_system != mavlinkSysId) return;

 		char name[MAVLINK_MSG_PARAM_REQUEST_READ_FIELD_PARAM_ID_LEN + 1];
 		strlcpy(name, m.param_id, sizeof(name)); // param_id might be not null-terminated
@@ -134,7 +125,7 @@ void handleMavlink(const void *_msg) {
 			memcpy(name, getParameterName(m.param_index), 16);
 		}
 		mavlink_message_t msg;
-		mavlink_msg_param_value_pack(SYSTEM_ID, MAV_COMP_ID_AUTOPILOT1, &msg,
+		mavlink_msg_param_value_pack(mavlinkSysId, MAV_COMP_ID_AUTOPILOT1, &msg,
 			name, value, MAV_PARAM_TYPE_REAL32, parametersCount(), m.param_index);
 		sendMessage(&msg);
 	}
@@ -142,14 +133,15 @@ void handleMavlink(const void *_msg) {
 	if (msg.msgid == MAVLINK_MSG_ID_PARAM_SET) {
 		mavlink_param_set_t m;
 		mavlink_msg_param_set_decode(&msg, &m);
-		if (m.target_system && m.target_system != SYSTEM_ID) return;
+		if (m.target_system && m.target_system != mavlinkSysId) return;

 		char name[MAVLINK_MSG_PARAM_SET_FIELD_PARAM_ID_LEN + 1];
 		strlcpy(name, m.param_id, sizeof(name)); // param_id might be not null-terminated
-		setParameter(name, m.param_value);
+		bool success = setParameter(name, m.param_value);
+		if (!success) return;
 		// send ack
 		mavlink_message_t msg;
-		mavlink_msg_param_value_pack(SYSTEM_ID, MAV_COMP_ID_AUTOPILOT1, &msg,
+		mavlink_msg_param_value_pack(mavlinkSysId, MAV_COMP_ID_AUTOPILOT1, &msg,
 			m.param_id, m.param_value, MAV_PARAM_TYPE_REAL32, parametersCount(), 0); // index is unknown
 		sendMessage(&msg);
 	}
@@ -157,17 +149,17 @@ void handleMavlink(const void *_msg) {
 	if (msg.msgid == MAVLINK_MSG_ID_MISSION_REQUEST_LIST) { // handle to make qgc happy
 		mavlink_mission_request_list_t m;
 		mavlink_msg_mission_request_list_decode(&msg, &m);
-		if (m.target_system && m.target_system != SYSTEM_ID) return;
+		if (m.target_system && m.target_system != mavlinkSysId) return;

 		mavlink_message_t msg;
-		mavlink_msg_mission_count_pack(SYSTEM_ID, MAV_COMP_ID_AUTOPILOT1, &msg, 0, 0, 0, MAV_MISSION_TYPE_MISSION, 0);
+		mavlink_msg_mission_count_pack(mavlinkSysId, MAV_COMP_ID_AUTOPILOT1, &msg, 0, 0, 0, MAV_MISSION_TYPE_MISSION, 0);
 		sendMessage(&msg);
 	}

 	if (msg.msgid == MAVLINK_MSG_ID_SERIAL_CONTROL) {
 		mavlink_serial_control_t m;
 		mavlink_msg_serial_control_decode(&msg, &m);
-		if (m.target_system && m.target_system != SYSTEM_ID) return;
+		if (m.target_system && m.target_system != mavlinkSysId) return;

 		char data[MAVLINK_MSG_SERIAL_CONTROL_FIELD_DATA_LEN + 1];
 		strlcpy(data, (const char *)m.data, m.count); // data might be not null-terminated
@@ -179,7 +171,7 @@ void handleMavlink(const void *_msg) {

 		mavlink_set_attitude_target_t m;
 		mavlink_msg_set_attitude_target_decode(&msg, &m);
-		if (m.target_system && m.target_system != SYSTEM_ID) return;
+		if (m.target_system && m.target_system != mavlinkSysId) return;

 		// copy attitude, rates and thrust targets
 		ratesTarget.x = m.body_roll_rate;
@@ -201,7 +193,7 @@ void handleMavlink(const void *_msg) {

 		mavlink_set_actuator_control_target_t m;
 		mavlink_msg_set_actuator_control_target_decode(&msg, &m);
-		if (m.target_system && m.target_system != SYSTEM_ID) return;
+		if (m.target_system && m.target_system != mavlinkSysId) return;

 		attitudeTarget.invalidate();
 		ratesTarget.invalidate();
@@ -213,12 +205,12 @@ void handleMavlink(const void *_msg) {
 	if (msg.msgid == MAVLINK_MSG_ID_LOG_REQUEST_DATA) {
 		mavlink_log_request_data_t m;
 		mavlink_msg_log_request_data_decode(&msg, &m);
-		if (m.target_system && m.target_system != SYSTEM_ID) return;
+		if (m.target_system && m.target_system != mavlinkSysId) return;

 		// Send all log records
 		for (int i = 0; i < sizeof(logBuffer) / sizeof(logBuffer[0]); i++) {
 			mavlink_message_t msg;
-			mavlink_msg_log_data_pack(SYSTEM_ID, MAV_COMP_ID_AUTOPILOT1, &msg, 0, i,
+			mavlink_msg_log_data_pack(mavlinkSysId, MAV_COMP_ID_AUTOPILOT1, &msg, 0, i,
 				sizeof(logBuffer[0]), (uint8_t *)logBuffer[i]);
 			sendMessage(&msg);
 		}
@@ -228,13 +220,13 @@ void handleMavlink(const void *_msg) {
 	if (msg.msgid == MAVLINK_MSG_ID_COMMAND_LONG) {
 		mavlink_command_long_t m;
 		mavlink_msg_command_long_decode(&msg, &m);
-		if (m.target_system && m.target_system != SYSTEM_ID) return;
+		if (m.target_system && m.target_system != mavlinkSysId) return;
 		mavlink_message_t response;
 		bool accepted = false;

 		if (m.command == MAV_CMD_REQUEST_MESSAGE && m.param1 == MAVLINK_MSG_ID_AUTOPILOT_VERSION) {
 			accepted = true;
-			mavlink_msg_autopilot_version_pack(SYSTEM_ID, MAV_COMP_ID_AUTOPILOT1, &response,
+			mavlink_msg_autopilot_version_pack(mavlinkSysId, MAV_COMP_ID_AUTOPILOT1, &response,
 				MAV_PROTOCOL_CAPABILITY_PARAM_FLOAT | MAV_PROTOCOL_CAPABILITY_MAVLINK2, 1, 0, 1, 1, 0, 0, 0, 0, 0, 0, 0);
 			sendMessage(&response);
 		}
@@ -253,7 +245,7 @@ void handleMavlink(const void *_msg) {

 		// send command ack
 		mavlink_message_t ack;
-		mavlink_msg_command_ack_pack(SYSTEM_ID, MAV_COMP_ID_AUTOPILOT1, &ack, m.command, accepted ? MAV_RESULT_ACCEPTED : MAV_RESULT_UNSUPPORTED, UINT8_MAX, 0, msg.sysid, msg.compid);
+		mavlink_msg_command_ack_pack(mavlinkSysId, MAV_COMP_ID_AUTOPILOT1, &ack, m.command, accepted ? MAV_RESULT_ACCEPTED : MAV_RESULT_UNSUPPORTED, UINT8_MAX, 0, msg.sysid, msg.compid);
 		sendMessage(&ack);
 	}
 }
@@ -270,7 +262,7 @@ void sendMavlinkPrint() {
 		char data[MAVLINK_MSG_SERIAL_CONTROL_FIELD_DATA_LEN + 1];
 		strlcpy(data, str + i, sizeof(data));
 		mavlink_message_t msg;
-		mavlink_msg_serial_control_pack(SYSTEM_ID, MAV_COMP_ID_AUTOPILOT1, &msg,
+		mavlink_msg_serial_control_pack(mavlinkSysId, MAV_COMP_ID_AUTOPILOT1, &msg,
 			SERIAL_CONTROL_DEV_SHELL,
 			i + MAVLINK_MSG_SERIAL_CONTROL_FIELD_DATA_LEN < strlen(str) ? SERIAL_CONTROL_FLAG_MULTI : 0, // more chunks to go
 			0, 0, strlen(data), (uint8_t *)data, 0, 0);
@@ -278,5 +270,3 @@ void sendMavlinkPrint() {
 	}
 	mavlinkPrintBuffer.clear();
 }
-
-#endif
--- a/flix/motors.ino
+++ b/flix/motors.ino
@@ -17,7 +17,8 @@
 #define PWM_MIN 0
 #define PWM_MAX 1000000 / PWM_FREQUENCY

-// Motors array indexes:
+float motors[4]; // normalized motor thrusts in range [0..1]
+
 const int MOTOR_REAR_LEFT = 0;
 const int MOTOR_REAR_RIGHT = 1;
 const int MOTOR_FRONT_RIGHT = 2;
--- a/flix/parameters.ino
+++ b/flix/parameters.ino
@@ -9,13 +9,20 @@
 extern float channelZero[16];
 extern float channelMax[16];
 extern float rollChannel, pitchChannel, throttleChannel, yawChannel, armedChannel, modeChannel;
+extern int wifiMode, udpLocalPort, udpRemotePort;
+extern float rcLossTimeout, descendTime;

 Preferences storage;

 struct Parameter {
 	const char *name; // max length is 15 (Preferences key limit)
-	float *variable;
-	float value; // cache
+	bool integer;
+	union { float *f; int *i; }; // pointer to variable
+	float cache; // what's stored in flash
+	Parameter(const char *name, float *variable) : name(name), integer(false), f(variable) {};
+	Parameter(const char *name, int *variable) : name(name), integer(true), i(variable) {};
+	float getValue() const { return integer ? *i : *f; };
+	void setValue(const float value) { if (integer) *i = value; else *f = value; };
 };

 Parameter parameters[] = {
@@ -43,12 +50,18 @@ Parameter parameters[] = {
 	{"CTL_Y_RATE_MAX", &maxRate.z},
 	{"CTL_TILT_MAX", &tiltMax},
 	// imu
+	{"IMU_ROT_ROLL", &imuRotation.x},
+	{"IMU_ROT_PITCH", &imuRotation.y},
+	{"IMU_ROT_YAW", &imuRotation.z},
 	{"IMU_ACC_BIAS_X", &accBias.x},
 	{"IMU_ACC_BIAS_Y", &accBias.y},
 	{"IMU_ACC_BIAS_Z", &accBias.z},
 	{"IMU_ACC_SCALE_X", &accScale.x},
 	{"IMU_ACC_SCALE_Y", &accScale.y},
 	{"IMU_ACC_SCALE_Z", &accScale.z},
+	// estimate
+	{"EST_ACC_WEIGHT", &accWeight},
+	{"EST_RATES_LPF_A", &ratesFilter.alpha},
 	// rc
 	{"RC_ZERO_0", &channelZero[0]},
 	{"RC_ZERO_1", &channelZero[1]},
@@ -71,6 +84,17 @@ Parameter parameters[] = {
 	{"RC_THROTTLE", &throttleChannel},
 	{"RC_YAW", &yawChannel},
 	{"RC_MODE", &modeChannel},
+	// wifi
+	{"WIFI_MODE", &wifiMode},
+	{"WIFI_LOC_PORT", &udpLocalPort},
+	{"WIFI_REM_PORT", &udpRemotePort},
+	// mavlink
+	{"MAV_SYS_ID", &mavlinkSysId},
+	{"MAV_RATE_SLOW", &telemetrySlow.rate},
+	{"MAV_RATE_FAST", &telemetryFast.rate},
+	// safety
+	{"SF_RC_LOSS_TIME", &rcLossTimeout},
+	{"SF_DESCEND_TIME", &descendTime},
 };

 void setupParameters() {
@@ -78,10 +102,10 @@ void setupParameters() {
 	// Read parameters from storage
 	for (auto &parameter : parameters) {
 		if (!storage.isKey(parameter.name)) {
-			storage.putFloat(parameter.name, *parameter.variable);
+			storage.putFloat(parameter.name, parameter.getValue()); // store default value
 		}
-		*parameter.variable = storage.getFloat(parameter.name, *parameter.variable);
-		parameter.value = *parameter.variable;
+		parameter.setValue(storage.getFloat(parameter.name, 0));
+		parameter.cache = parameter.getValue();
 	}
 }

@@ -96,13 +120,13 @@ const char *getParameterName(int index) {

 float getParameter(int index) {
 	if (index < 0 || index >= parametersCount()) return NAN;
-	return *parameters[index].variable;
+	return parameters[index].getValue();
 }

 float getParameter(const char *name) {
 	for (auto &parameter : parameters) {
-		if (strcmp(parameter.name, name) == 0) {
-			return *parameter.variable;
+		if (strcasecmp(parameter.name, name) == 0) {
+			return parameter.getValue();
 		}
 	}
 	return NAN;
@@ -110,8 +134,9 @@ float getParameter(const char *name) {

 bool setParameter(const char *name, const float value) {
 	for (auto &parameter : parameters) {
-		if (strcmp(parameter.name, name) == 0) {
-			*parameter.variable = value;
+		if (strcasecmp(parameter.name, name) == 0) {
+			if (parameter.integer && !isfinite(value)) return false; // can't set integer to NaN or Inf
+			parameter.setValue(value);
 			return true;
 		}
 	}
@@ -124,16 +149,18 @@ void syncParameters() {
 	if (motorsActive()) return; // don't use flash while flying, it may cause a delay

 	for (auto &parameter : parameters) {
-		if (parameter.value == *parameter.variable) continue;
-		if (isnan(parameter.value) && isnan(*parameter.variable)) continue; // handle NAN != NAN
-		storage.putFloat(parameter.name, *parameter.variable);
-		parameter.value = *parameter.variable;
+		if (parameter.getValue() == parameter.cache) continue; // no change
+		if (isnan(parameter.getValue()) && isnan(parameter.cache)) continue; // both are NaN
+		if (isinf(parameter.getValue()) && isinf(parameter.cache)) continue; // both are Inf
+
+		storage.putFloat(parameter.name, parameter.getValue());
+		parameter.cache = parameter.getValue(); // update cache
 	}
 }

 void printParameters() {
 	for (auto &parameter : parameters) {
-		print("%s = %g\n", parameter.name, *parameter.variable);
+		print("%s = %g\n", parameter.name, parameter.getValue());
 	}
 }

--- a/flix/rc.ino
+++ b/flix/rc.ino
@@ -6,14 +6,17 @@
 #include <SBUS.h>
 #include "util.h"

-SBUS rc(Serial2); // NOTE: Use RC(Serial2, 16, 17) if you use the old UART2 pins
+SBUS rc(Serial2);

 uint16_t channels[16]; // raw rc channels
-float controlTime; // time of the last controls update
 float channelZero[16]; // calibration zero values
 float channelMax[16]; // calibration max values

-// Channels mapping (using float to store in parameters):
+float controlRoll, controlPitch, controlYaw, controlThrottle; // pilot's inputs, range [-1, 1]
+float controlMode = NAN;
+float controlTime = NAN; // time of the last controls update
+
+// Channels mapping (nan means not assigned):
 float rollChannel = NAN, pitchChannel = NAN, throttleChannel = NAN, yawChannel = NAN, modeChannel = NAN;

 void setupRC() {
@@ -38,11 +41,11 @@ void normalizeRC() {
 		controls[i] = mapf(channels[i], channelZero[i], channelMax[i], 0, 1);
 	}
 	// Update control values
-	controlRoll = rollChannel >= 0 ? controls[(int)rollChannel] : NAN;
-	controlPitch = pitchChannel >= 0 ? controls[(int)pitchChannel] : NAN;
-	controlYaw = yawChannel >= 0 ? controls[(int)yawChannel] : NAN;
-	controlThrottle = throttleChannel >= 0 ? controls[(int)throttleChannel] : NAN;
-	controlMode = modeChannel >= 0 ? controls[(int)modeChannel] : NAN;
+	controlRoll = rollChannel >= 0 ? controls[(int)rollChannel] : 0;
+	controlPitch = pitchChannel >= 0 ? controls[(int)pitchChannel] : 0;
+	controlYaw = yawChannel >= 0 ? controls[(int)yawChannel] : 0;
+	controlThrottle = throttleChannel >= 0 ? controls[(int)throttleChannel] : 0;
+	controlMode = modeChannel >= 0 ? controls[(int)modeChannel] : NAN; // mode switch should not have affect if not set
 }

 void calibrateRC() {
--- a/flix/safety.ino
+++ b/flix/safety.ino
@@ -3,12 +3,12 @@

 // Fail-safe functions

-#define RC_LOSS_TIMEOUT 1
-#define DESCEND_TIME 10
-
 extern float controlTime;
 extern float controlRoll, controlPitch, controlThrottle, controlYaw;

+float rcLossTimeout = 1;
+float descendTime = 10;
+
 void failsafe() {
 	rcLossFailsafe();
 	autoFailsafe();
@@ -16,9 +16,8 @@ void failsafe() {

 // RC loss failsafe
 void rcLossFailsafe() {
-	if (controlTime == 0) return; // no RC at all
 	if (!armed) return;
-	if (t - controlTime > RC_LOSS_TIMEOUT) {
+	if (t - controlTime > rcLossTimeout) {
 		descend();
 	}
 }
@@ -27,7 +26,7 @@ void rcLossFailsafe() {
 void descend() {
 	mode = AUTO;
 	attitudeTarget = Quaternion();
-	thrustTarget -= dt / DESCEND_TIME;
+	thrustTarget -= dt / descendTime;
 	if (thrustTarget < 0) {
 		thrustTarget = 0;
 		armed = false;
--- a/flix/time.ino
+++ b/flix/time.ino
@@ -3,6 +3,8 @@

 // Time related functions

+float t = NAN; // current time, s
+float dt; // time delta with the previous step, s
 float loopRate; // Hz

 void step() {
--- a/flix/vector.h
+++ b/flix/vector.h
@@ -35,7 +35,6 @@ public:
 		z = NAN;
 	}

-
 	float norm() const {
 		return sqrt(x * x + y * y + z * z);
 	}
--- a/flix/wifi.ino
+++ b/flix/wifi.ino
@@ -1,45 +1,76 @@
 // Copyright (c) 2023 Oleg Kalachev <okalachev@gmail.com>
 // Repository: https://github.com/okalachev/flix

-// Wi-Fi support
-
-#if WIFI_ENABLED
+// Wi-Fi communication

 #include <WiFi.h>
 #include <WiFiAP.h>
 #include <WiFiUdp.h>
+#include "Preferences.h"

-#define WIFI_AP_MODE 1
-#define WIFI_AP_SSID "flix"
-#define WIFI_AP_PASSWORD "flixwifi"
-#define WIFI_SSID ""
-#define WIFI_PASSWORD ""
-#define WIFI_UDP_PORT 14550
-#define WIFI_UDP_REMOTE_PORT 14550
-#define WIFI_UDP_REMOTE_ADDR "255.255.255.255"
+extern Preferences storage; // use the main preferences storage
+
+const int W_DISABLED = 0, W_AP = 1, W_STA = 2;
+int wifiMode = W_AP;
+int udpLocalPort = 14550;
+int udpRemotePort = 14550;
+IPAddress udpRemoteIP = "255.255.255.255";

 WiFiUDP udp;

 void setupWiFi() {
 	print("Setup Wi-Fi\n");
-	if (WIFI_AP_MODE) {
-		WiFi.softAP(WIFI_AP_SSID, WIFI_AP_PASSWORD);
-	} else {
-		WiFi.begin(WIFI_SSID, WIFI_PASSWORD);
+	if (wifiMode == W_AP) {
+		WiFi.softAP(storage.getString("WIFI_AP_SSID", "flix").c_str(), storage.getString("WIFI_AP_PASS", "flixwifi").c_str());
+	} else if (wifiMode == W_STA) {
+		WiFi.begin(storage.getString("WIFI_STA_SSID", "").c_str(), storage.getString("WIFI_STA_PASS", "").c_str());
 	}
-	udp.begin(WIFI_UDP_PORT);
+	udp.begin(udpLocalPort);
 }

 void sendWiFi(const uint8_t *buf, int len) {
-	if (WiFi.softAPIP() == IPAddress(0, 0, 0, 0) && WiFi.status() != WL_CONNECTED) return;
-	udp.beginPacket(udp.remoteIP() ? udp.remoteIP() : WIFI_UDP_REMOTE_ADDR, WIFI_UDP_REMOTE_PORT);
+	if (WiFi.softAPgetStationNum() == 0 && !WiFi.isConnected()) return;
+	udp.beginPacket(udpRemoteIP, udpRemotePort);
 	udp.write(buf, len);
 	udp.endPacket();
 }

 int receiveWiFi(uint8_t *buf, int len) {
 	udp.parsePacket();
+	if (udp.remoteIP()) udpRemoteIP = udp.remoteIP();
 	return udp.read(buf, len);
 }

-#endif
+void printWiFiInfo() {
+	if (WiFi.getMode() == WIFI_MODE_AP) {
+		print("Mode: Access Point (AP)\n");
+		print("MAC: %s\n", WiFi.softAPmacAddress().c_str());
+		print("SSID: %s\n", WiFi.softAPSSID().c_str());
+		print("Password: ***\n");
+		print("Clients: %d\n", WiFi.softAPgetStationNum());
+		print("IP: %s\n", WiFi.softAPIP().toString().c_str());
+	} else if (WiFi.getMode() == WIFI_MODE_STA) {
+		print("Mode: Client (STA)\n");
+		print("Connected: %d\n", WiFi.isConnected());
+		print("MAC: %s\n", WiFi.macAddress().c_str());
+		print("SSID: %s\n", WiFi.SSID().c_str());
+		print("Password: ***\n");
+		print("IP: %s\n", WiFi.localIP().toString().c_str());
+	} else {
+		print("Mode: Disabled\n");
+		return;
+	}
+	print("Remote IP: %s\n", udpRemoteIP.toString().c_str());
+	print("MAVLink connected: %d\n", mavlinkConnected);
+}
+
+void configWiFi(bool ap, const char *ssid, const char *password) {
+	if (ap) {
+		storage.putString("WIFI_AP_SSID", ssid);
+		storage.putString("WIFI_AP_PASS", password);
+	} else {
+		storage.putString("WIFI_STA_SSID", ssid);
+		storage.putString("WIFI_STA_PASS", password);
+	}
+	print("✓ Reboot to apply new settings\n");
+}
--- a/gazebo/README.md
+++ b/gazebo/README.md
@@ -68,6 +68,9 @@ Just like the real drone, the simulator can be controlled using a USB remote con
 6. Go to the settings and enable *Virtual Joystick*. *Auto-Center Throttle* setting **should be disabled**.
 7. Use the virtual joystick to fly the drone!

+> [!TIP]
+> Decrease `CTL_TILT_MAX` parameter when flying using the smartphone to make the controls less sensitive.
+
 ### Control with USB remote control

 1. Connect your USB remote control to the machine running the simulator.
--- a/gazebo/flix.h
+++ b/gazebo/flix.h
@@ -10,18 +10,15 @@
 #include "Arduino.h"
 #include "wifi.h"

-#define WIFI_ENABLED 1
+extern float t, dt;
+extern float controlRoll, controlPitch, controlYaw, controlThrottle, controlMode;
+extern Vector rates;
+extern Quaternion attitude;
+extern bool landed;
+extern float motors[4];

-float t = NAN;
-float dt;
-float motors[4];
-float controlRoll, controlPitch, controlYaw, controlThrottle = NAN;
-float controlMode = NAN;
-Vector acc;
-Vector gyro;
-Vector rates;
-Quaternion attitude;
-bool landed;
+Vector gyro, acc, imuRotation;
+Vector accBias, gyroBias, accScale(1, 1, 1);

 // declarations
 void step();
@@ -73,4 +70,5 @@ void calibrateGyro() { print("Skip gyro calibrating\n"); };
 void calibrateAccel() { print("Skip accel calibrating\n"); };
 void printIMUCalibration() { print("cal: N/A\n"); };
 void printIMUInfo() {};
-Vector accBias, gyroBias, accScale(1, 1, 1);
+void printWiFiInfo() {};
+void configWiFi(bool, const char*, const char*) { print("Skip WiFi config\n"); };
--- a/tools/log.py
+++ b/tools/log.py
@@ -43,6 +43,7 @@ records = [record for record in records if record[0] != 0]

 print(f'Received records: {len(records)}')

+os.makedirs(f'{DIR}/log', exist_ok=True)
 log = open(f'{DIR}/log/{datetime.datetime.now().isoformat()}.csv', 'wb')
 log.write(header.encode() + b'\n')
 for record in records:
--- a/tools/pyflix/README.md
+++ b/tools/pyflix/README.md
@@ -1,8 +1,8 @@
 # Flix Python library

-The Flix Python library allows you to remotely connect to a Flix quadcopter. It provides access to telemetry data, supports executing CLI commands, and controlling the drone's flight.
+The Flix Python library allows you to remotely connect to a Flix quadcopter. It provides access to telemetry data, supports executing console commands, and controlling the drone's flight.

-To use the library, connect to the drone's Wi-Fi. To use it with the simulator, ensure the script runs on the same local network as the simulator.
+To use the library, connect to the drone's Wi-Fi. To use it with the simulator, ensure the script runs on the same network as the simulator.

 ## Installation

@@ -30,7 +30,7 @@ flix = Flix()  # create a Flix object and wait for connection

 ### Telemetry

-Basic telemetry is available through object properties. The properties names generally match the corresponding variables in the firmware itself:
+Basic telemetry is available through object properties. The property names generally match the corresponding variables in the firmware itself:

 ```python
 print(flix.connected)       # True if connected to the drone
@@ -41,7 +41,7 @@ print(flix.attitude)        # attitude quaternion [w, x, y, z]
 print(flix.attitude_euler)  # attitude as Euler angles [roll, pitch, yaw]
 print(flix.rates)           # angular rates [roll_rate, pitch_rate, yaw_rate]
 print(flix.channels)        # raw RC channels (list)
-print(flix.motors)          # motors outputs (list)
+print(flix.motors)          # motor outputs (list)
 print(flix.acc)             # accelerometer output (list)
 print(flix.gyro)            # gyroscope output (list)
 ```
@@ -95,24 +95,24 @@ Full list of events:
 |`armed`|Armed state update|Armed state (*bool*)|
 |`mode`|Flight mode update|Flight mode (*str*)|
 |`landed`|Landed state update|Landed state (*bool*)|
-|`print`|The drone sends text to the console|Text|
+|`print`|The drone prints text to the console|Text|
 |`attitude`|Attitude update|Attitude quaternion (*list*)|
 |`attitude_euler`|Attitude update|Euler angles (*list*)|
 |`rates`|Angular rates update|Angular rates (*list*)|
 |`channels`|Raw RC channels update|Raw RC channels (*list*)|
-|`motors`|Motors outputs update|Motors outputs (*list*)|
+|`motors`|Motor outputs update|Motor outputs (*list*)|
 |`acc`|Accelerometer update|Accelerometer output (*list*)|
 |`gyro`|Gyroscope update|Gyroscope output (*list*)|
 |`mavlink`|Received MAVLink message|Message object|
 |`mavlink.<message_name>`|Received specific MAVLink message|Message object|
 |`mavlink.<message_id>`|Received specific MAVLink message|Message object|
 |`value`|Named value update (see below)|Name, value|
-|`value.<name>`|Specific named value update (see bellow)|Value|
+|`value.<name>`|Specific named value update (see below)|Value|

 > [!NOTE]
-> Update events trigger on every new data from the drone, and do not mean the value has changed.
+> Update events trigger on every new piece of data from the drone, and do not mean the value has changed.

-### Common methods
+### Basic methods

 Get and set firmware parameters using `get_param` and `set_param` methods:

@@ -121,7 +121,7 @@ pitch_p = flix.get_param('PITCH_P')  # get parameter value
 flix.set_param('PITCH_P', 5)         # set parameter value
 ```

-Execute console commands using `cli` method. This method returns command response:
+Execute console commands using `cli` method. This method returns the command response:

 ```python
 imu = flix.cli('imu')    # get detailed IMU data
@@ -169,10 +169,10 @@ Setting angular rates target:
 flix.set_rates([0.1, 0.2, 0.3], 0.6)  # set target roll rate, pitch rate, yaw rate and thrust
 ```

-You also can control raw motors outputs directly:
+You also can control raw motor outputs directly:

 ```python
-flix.set_motors([0.5, 0.5, 0.5, 0.5])  # set motors outputs in range [0, 1]
+flix.set_motors([0.5, 0.5, 0.5, 0.5])  # set motor outputs in range [0, 1]
 ```

 In *AUTO* mode, the drone will arm automatically if the thrust is greater than zero, and disarm if thrust is zero. Therefore, to disarm the drone, set thrust to zero:
@@ -186,7 +186,7 @@ The following methods are in development and are not functional yet:
 * `set_position` — set target position.
 * `set_velocity` — set target velocity.

-To exit from *AUTO* mode move control sticks and the drone will switch to *STAB* mode.
+To exit *AUTO* mode move control sticks and the drone will switch to *STAB* mode.

 ## Usage alongside QGroundControl

--- a/tools/pyflix/flix.py
+++ b/tools/pyflix/flix.py
@@ -17,7 +17,7 @@ from pymavlink.dialects.v20 import common as mavlink
 logger = logging.getLogger('flix')
 if not logger.hasHandlers():
    handler = logging.StreamHandler()
-    handler.setFormatter(logging.Formatter('%(name)s - %(levelname)s - %(message)s'))
+    handler.setFormatter(logging.Formatter('%(name)s: %(message)s'))
    logger.addHandler(handler)
    logger.setLevel(logging.INFO)

@@ -40,7 +40,7 @@ class Flix:

    _connection_timeout = 3
    _print_buffer: str = ''
-    _modes = ['MANUAL', 'ACRO', 'STAB', 'AUTO']
+    _modes = ['RAW', 'ACRO', 'STAB', 'AUTO']

    def __init__(self, system_id: int=1, wait_connection: bool=True):
        if not (0 <= system_id < 256):
--- a/tools/pyproject.toml
+++ b/tools/pyproject.toml
@@ -1,6 +1,6 @@
 [project]
 name = "pyflix"
-version = "0.9"
+version = "0.11"
 description = "Python API for Flix drone"
 authors = [{ name="Oleg Kalachev", email="okalachev@gmail.com" }]
 license = "MIT"
Author	SHA1	Message	Date
Oleg Kalachev	5b654e4d8e	Update ESP32-Core to 3.3.6	2026-01-23 02:41:43 +03:00
Oleg Kalachev	cf10ec6161	Update MAVLink-Arduino to 2.0.16	2026-01-23 01:11:35 +03:00
Oleg Kalachev	6d01cd2e79	Make failsafe configurable using parameters SF_RC_LOSS_TIME - time without rc to activate failsafe. SD_DESCEND_TIME - total time to decrease the throttle to zero. Make controlTime nan on the start to simplify the logic.	2026-01-22 23:57:52 +03:00
Oleg Kalachev	0abb18c616	Make parameter names case-insensitive + minor fix	2026-01-22 23:11:47 +03:00
Oleg Kalachev	30326a5662	Add parameters for configuring the mavlink subsystem MAV_SYS_ID - mavlink system id. MAV_RATE_SLOW - rate of slow telemetry (e. g. heartbeats). MAV_RATE_FAST - rate of fast telemetry (e. g. attitude, imu data).	2026-01-22 23:04:45 +03:00
Oleg Kalachev	dd3575174b	Add wifi configuration using parameters and cli Add console commands to setup wifi. Add a parameter for choosing between STA and AP mode. Add parameters for udp ports. Remove WIFI_ENABLED macro.	2026-01-22 22:58:43 +03:00
Oleg Kalachev	c0f3301da4	Support integer parameters in addition to floats The variable pointer is stored as a union field. If `.integer` field is true, then integer pointer should be used. Interfaces to parameters (cli and mavlink) keep working using floats. Setting a non-finite value to int parameter will cause an error. `.value` field is renamed to `.cache`.	2026-01-22 22:54:05 +03:00
a.golubtsov	a6bad3a69b	Add log dir creation before log writing	2026-01-22 17:56:23 +03:00
Oleg Kalachev	9a9bd07251	Add correct attitude estimation video to the usage article	2026-01-15 23:46:23 +03:00
Oleg Kalachev	28f5855a57	Re-arrange control.ino declarations to make a bit more sensible So the control command is above the PID controllers.	2026-01-13 17:43:53 +03:00
Oleg Kalachev	7e24ee30f7	Documentation and book updates Improve the main list of features. Use lowercase imu variable for consistency with the firmware code. Minor fixes.	2026-01-13 17:26:40 +03:00
Oleg Kalachev	2a8faf5759	Fix logo svg slightly	2026-01-08 19:45:08 +03:00
Oleg Kalachev	f4e58a652a	Add project logo	2026-01-08 17:58:59 +03:00
Oleg Kalachev	6c46328da1	Minor doc fixes	2026-01-04 15:01:53 +03:00
Oleg Kalachev	c8e5e08b03	Move all global variable declarations to the appropriate subsystems As it makes the subsystems code easier to understand. Declare the most used variables in main sketch file as forward declarations. Make all control input zero by default (except controlMode). Minor changes.	2026-01-03 13:28:18 +03:00
Oleg Kalachev	a5e3dfcf69	Some updates to the docs	2026-01-03 12:18:47 +03:00
Oleg Kalachev	d6e8be0c05	Add parameters for easier IMU orientation definition	2025-12-26 21:14:15 +03:00
Oleg Kalachev	68d16855df	Add motors rotation diagram to usage article	2025-12-25 07:22:09 +03:00
Oleg Kalachev	0547ea548b	Add parameters for acc weight and rates lpf alpha	2025-12-24 05:43:55 +03:00
Oleg Kalachev	c02dba6812	Rename gyroCalibrationFilter to gyroBiasFilter Which seems a better name	2025-12-24 05:36:43 +03:00
Oleg Kalachev	f1dc4a0400	Updates to user builds article	2025-12-17 02:21:51 +03:00
Oleg Kalachev	158827ac55	Add new user builds, add school 548 course overview + minor doc fixes.	2025-12-13 21:09:33 +03:00
Oleg Kalachev	36ca30c3e4	Minor docs fix	2025-11-27 18:34:32 +03:00
Oleg Kalachev	48711b55e1	Add tip about CNT_TILT_MAX parameter to the simulator article	2025-11-26 17:34:08 +03:00
Oleg Kalachev	4d583185a9	Rename manual mode to raw mode Make it callable from the console. Increase the coefficient. Corresponding change in pyflix. pyflix@0.11.	2025-11-25 04:44:16 +03:00
Oleg Kalachev	d757ffa853	Move yaw dead zone handling from mavlink to control subsystem So yaw dead zone works the same for rc and mavlink.	2025-11-22 05:11:46 +03:00
Oleg Kalachev	5352386486	Minor updates to pyflix library, pyflix@0.10 Fixes to documentation. Improve logger format.	2025-11-22 05:07:46 +03:00
Oleg Kalachev	9b5872740f	Add wifi cli command To show wi-fi info.	2025-11-22 04:46:54 +03:00
Oleg Kalachev	31dbdaf241	Group control parameters Also add IMU group to accelerometer calibration parameters.	2025-11-19 01:50:46 +03:00
Oleg Kalachev	f4b56262b1	Remove unneeded SERIAL_BAUDRATE define	2025-11-14 20:23:15 +03:00
Oleg Kalachev	49039f752d	Refactor Wi-Fi log download Use MAVLink LOG_REQUEST_DATA and LOG_DATA for download log instead of console. Make Wi-Fi download default way of downloading the log. Make `log` command only print the header and `log dump` dump the log.	2025-11-14 20:21:05 +03:00
Oleg Kalachev	348721acc9	Updates in documentation Fixes, updates, new illustrations.	2025-11-10 20:16:14 +03:00
Oleg Kalachev	774144c430	Many updates to documentation Updates to main readme. Add much more info to usage article. Move simulator building to simulation's readme. Improve assembly article. Many fixes. Updates in diagrams.	2025-11-06 13:55:52 +03:00
Oleg Kalachev	0e6651ab82	Add Rate class for running the code at fixed rate	2025-11-06 13:41:33 +03:00
Oleg Kalachev	1a017ccb97	Keep only one floating point version of map function Two variants are redundant	2025-11-02 00:02:28 +03:00
Oleg Kalachev	7170b20d1d	Simplify command for command handling	2025-10-21 19:41:10 +03:00
Oleg Kalachev	dc9aed113b	Minor code fixes	2025-10-21 19:41:05 +03:00
Oleg Kalachev	08b6123eb7	Fixes to troubleshooting	2025-10-21 19:40:54 +03:00
Oleg Kalachev	1a8b63ee04	Send only mavlink heartbeats until connected	2025-10-21 19:39:17 +03:00
Oleg Kalachev	8c49a40516	Skip attitude/rate control if thrustTarget is ineffective To prevent i term windup.	2025-10-20 23:01:17 +03:00
Oleg Kalachev	ca595edce5	Refactor PID control to simplify the code and modifications Each PID uses its internal dt, so may be various contexts with different rate. PID has max dt, so no need to reset explicitly.	2025-10-20 22:54:18 +03:00
KiraFlux	d06eb2a1aa	Quaternion::fromBetweenVectors: pass u and v as const references (#21 )	2025-10-19 20:46:46 +03:00
Oleg Kalachev	e50a9d5fea	Revert t variable type to float instead of double For the sake of simplicity and consistency.	2025-10-19 20:46:38 +03:00
Oleg Kalachev	ebac78dc0f	Minor change	2025-10-19 20:46:26 +03:00
Oleg Kalachev	186cf88d84	Add generic Delay filter	2025-10-19 20:46:11 +03:00
Oleg Kalachev	253aae2220	Lowercase imu and rc variables To make it more obvious these are variables, not classes.	2025-10-19 20:45:56 +03:00
Oleg Kalachev	6f0964fac4	Rename failsafe.ino to safety.ino To aggregate all the safety related functionality.	2025-10-19 20:44:54 +03:00
Oleg Kalachev	1d034f268d	Add ESP32-S3 build to Actions	2025-10-19 20:44:46 +03:00
Oleg Kalachev	1ca7d32862	Update VSCode settings Disable error squiggles as they often work incorrectly. Decrease number of include libraries to index.	2025-10-14 11:43:55 +03:00
Oleg Kalachev	ab941e34fa	Fix Gazebo installation Installation script is deprecated, install using package on Ubuntu 20.04	2025-10-13 18:56:14 +03:00
Oleg Kalachev	7bee3d1751	Improve rc failsafe logic Don't trigger failsafe if there's no RC at all Use AUTO mode for descending, instead of STAB Increase RC loss timeout and descend time	2025-10-12 21:27:08 +03:00
Oleg Kalachev	06ec5f3160	Disarm the drone on simulator plugin reset In order to reset yaw target.	2025-10-07 15:45:48 +03:00
Oleg Kalachev	c4533e3ac8	Reset yaw target when drone disarmed Prevent unexpected behavior when the drone tries to restore its old yaw on takeoff.	2025-10-07 15:43:28 +03:00
Oleg Kalachev	e673b50f52	Include FlixPeriph header instead of MPU9250 This simplifies choosing IMU model	2025-10-07 08:43:12 +03:00
Oleg Kalachev	5151bb9133	Ensure showing correct raw data in imu command Some IMUs will reset acc and gyro buffer on whoAmI() call	2025-10-07 08:43:06 +03:00